HardLabs

CrealitySpacePiAutomation

Ermakov·CrealitySpacePiAutomation·CrealityDryerArduinoPCB(KiCad8)/CrealityDryerV1.kicad_pcb

CrealitySpacePiAutomation PCB layout, top view — open source AVR/Arduino board by Ermakov

About the CrealitySpacePiAutomation PCB

CrealitySpacePiAutomation is an open source AVR/Arduino PCB design by Ermakov, published on GitHub. It is a 2-layer board measuring 39.9 × 46.4 mm, with 19 components from 15 distinct parts.

Its main chip is the Arduino_Nano_v2.x, from the AVR/Arduino family. Other key parts include the ATmega328P-A. By type, the board carries 6 capacitors, 5 connectors, 4 resistors, 1 IC, 1 module and 1 crystal.

It belongs with the sensors designs in this gallery, and the repository also holds 1 earlier revision of it.

From the project

Creality Space Pi Plus CFS mod automation (PCB and sketch for Arduino IDE)

Description: - necessary the module itself and IDC10 female-male cable - can be inserted into any Creality SpacePi dryer (double, single, built-in Creality CFS or not) - other functions and cables are optional (backlights, external control and power are not required for operation, but can be connected additionally) - the cable from the SpacePi display needs to be disconnected from the dryer board and inserted into the "display" socket on the module - an additional IDC10 cable connecting between the module "mainboard" socket and the dryer board (power is supplied from the dryer board via this…

Main components on the CrealitySpacePiAutomation

ATmega328P-AArduino_Nano_v2.x

CrealitySpacePiAutomation bill of materials (BOM)

19 components, 15 distinct parts.

QtyPartRefs
1
ATmega328P-A
U2
1
Arduino_Nano_v2.x
A1
1
16MHz
Y1
1
8P8C
J1
1
MainBoard
J2
1
Display
J3
1
PROG
J5
1
PWR
J6
1
SS14
D1
3
100nF
C1, C3, C4
1
22uF 10V
C2
2
10pF
C5, C6
2
10K
R2, R3
1
1K
RN1
1
100R
RN2

CrealitySpacePiAutomation design files

The KiCad project lives in the Ermakov/CrealitySpacePiAutomation repository on GitHub; these links point at the commit this page was built from.

CrealitySpacePiAutomation: common questions

What microcontroller does the CrealitySpacePiAutomation use?

The CrealitySpacePiAutomation is built around the Arduino_Nano_v2.x, from the AVR/Arduino family.

How big is the CrealitySpacePiAutomation PCB?

The CrealitySpacePiAutomation measures 39.9 × 46.4 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the CrealitySpacePiAutomation?

19 components, from 15 distinct parts. The full bill of materials is listed on this page.

Where can I download the CrealitySpacePiAutomation design files?

From the Ermakov/CrealitySpacePiAutomation repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the CrealitySpacePiAutomation design in my own project?

The repository has no license, so all rights stay with Ermakov. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the CrealitySpacePiAutomation without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Earlier revisions in the repo: CrealityDryer

Similar boards