134 open source boards using the ATmega328P-A
Real designs built with the ATmega328P-A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
RFBitBangSMT
profdc9
152 × 88 mm263 parts2LNo license221AVR/Arduino
Vx8 gps
4x1md
43.5 × 43.5 mm30 parts2LMIT65AVR/Arduino
SmartPortSD SMD
djtersteegc
41 × 50 mm24 parts2LMIT54AVR/Arduino
Twelvekey
str-dst
75.2 × 62.6 mm52 parts2LCC-BY-NC-4.049AVR/Arduino
Entropy32-Plus
captainchapster
53 × 63 mm34 parts2LMIT37AVR/Arduino
4chord midi
sgreg
74.8 × 84.7 mm60 parts2LNo license36AVR/Arduino
ModularLabPSU
tom-biskupic
128 × 80 mm140 parts2LNo license33AVR/Arduino
IBus BT digital module
the-vty
60 × 40 mm56 parts2LLGPL-3.033AVR/Arduino
CrealitySpacePiAutomation
Ermakov
39.9 × 46.4 mm19 parts2LNo license33ESP8266
Split flap fae
codingcatgirl
40 × 80 mm39 parts2LApache-2.030Microchip SAM
StratoSoar-MK2.2
crnicholson
42 × 84 mm107 parts4LNo license24AVR/Arduino
Divergence Meter Control Board
q61org
89 × 47 mm102 parts2LNo license21AVR/Arduino
DSKY
Apollo-Replica
169.9 × 190.9 mm116 parts2LCC-BY-NC-4.020AVR/Arduino
SparkAltBatteryBoard
fahreddinaykut
58.8 × 29 mm37 parts4LMIT20AVR/Arduino
Nixiepipe hardware
tuna-f1sh
48.2 × 49.3 mm45 parts2LCC-BY-SA-4.019AVR/Arduino
Oscillator Board
Bad-Dog-Designs
229 × 96 mm132 parts2LNo license18AVR/Arduino
DigitalTemperatureController
charlesbaynham
80 × 100 mm163 parts4LNo license14- schematic only · 244 partsAVR/Arduino
PhotonSaw
openspaceaarhus
244 partsApache-2.013 AVR/Arduino
GP22 RF Photon Correllation
charlesbaynham
100 × 100 mm116 parts4LNo license11AVR/Arduino
TX5823
ep092
54.5 × 47.6 mm94 parts2LNo license9AVR/Arduino
RHS 3
pa-pa
51 × 61 mm66 parts2LNo license9AVR/Arduino
Nixie control board
shengwen-tw
183.8 × 59.4 mm61 parts2LMIT9AVR/Arduino
PWM-Solar-Charge-Controller
Duckle29
58.4 × 66.7 mm51 parts2LMIT9AVR/Arduino
PiLeven
freetronics
84.5 × 56 mm67 parts2LTAPR-OHL-1.06AVR/Arduino
Handystick panel
kjoller
49.5 × 45 mm25 parts2LCERN-OHL-1.26AVR/Arduino
BoardGame
jkordek1
150 × 150 mm176 parts2LNo license5AVR/Arduino
Ultimate temperature controller
Technariumas
80 × 100 mm68 parts2LApache-2.04AVR/Arduino
Ws 3.0
boanjo
72.7 × 114 mm53 parts2LNo license4ESP8266
Rodi
rodibot
50 × 50 mm48 parts2LNo license4AVR/Arduino
Tapecart sd vertical
djtersteegc
45.4 × 50 mm33 parts2LMIT4AVR/Arduino
Bullion
coddingtonbear
38.8 × 27.3 mm21 parts2LNo license3AVR/Arduino
Solar lora
mattvenn
60 × 60 mm45 parts2LNo license2AVR/Arduino
Uedaino
fabkominka
50 × 65 mm30 parts2LNo license2AVR/Arduino
Solari control
kmzbrnoI
80 × 90 mm106 parts2LNo license1AVR/Arduino
Car
le-flav-b
50 × 67 mm94 parts2LNo license1AVR/Arduino
Segment Display Board
FRC-1721
58.4 × 141 mm90 parts2LNo license1
How designs wire the ATmega328P-A
Read from the KiCad layouts of 103 open source designs, one per repository: what each pin of the ATmega328P-A connects to, and the resistors, capacitors and other passives placed on it.
- The XTAL1/PB6 pin has a crystal on 92 of 102 designs, most often 16 MHz (then 8 MHz).
- The XTAL2/PB7 pin has a crystal on 92 of 103 designs, most often 16 MHz (then 8 MHz).
- The RESET/PC6 pin has a pull-up to 5V on 87 of 102 designs, most often 10 kΩ (then 1 kΩ).
- The XTAL1/PB6 pin has a capacitor to GND on 75 of 102 designs, most often 22 pF (then 12 pF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 3, 5, 21 | Connected to: GND 96% | — |
| VCCpin 4, 6 | Connected to: 5V 92% |
|
| XTAL1/PB6pin 7 | Connected to: Signal 93% |
|
| XTAL2/PB7pin 8 | Connected to: Signal 94% |
|
| AVCCpin 18 | Connected to: 5V 85% |
|
| ADC6pin 19 | Connected to: Not connected 70% · a signal 30% | — |
| AREFpin 20 | Connected to: Signal 71% · not connected 18% |
|
| ADC7pin 22 | Connected to: Not connected 75% · a signal 25% | — |
| RESET/PC6pin 29 | Connected to: A connector 81% |
|
20 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Easyduino Atmega by Hanqaqa, OSBMS MicroMaster atmega328 by Teslafly, RFBitBangSMT by profdc9 and RHS PCB by dmcke5.
The ATmega328P-A in open source designs
The gallery holds 134 open source boards using the ATmega328P-A from 109 GitHub repositories; a typical one measures about 60 × 59.4 mm and carries around 48 components.
83% are two-layer designs, the rest use four layers or more, and 30% carry an open source license.
The most starred is Easyduino Atmega by Hanqaqa.
Parts used alongside the ATmega328P-A
Microcontrollers on boards using the ATmega328P-A
What boards using the ATmega328P-A are built for
ATmega328P-A: common questions
Where can I find a ATmega328P-A reference design?
Each of the 134 boards on this page is a real design using the ATmega328P-A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ATmega328P-A XTAL1/PB6 pin connected?
The XTAL1/PB6 pin has a crystal on 92 of 102 designs, most often 16 MHz (then 8 MHz). Counted from the KiCad layouts of 103 open source designs using the ATmega328P-A.
How is the ATmega328P-A XTAL2/PB7 pin connected?
The XTAL2/PB7 pin has a crystal on 92 of 103 designs, most often 16 MHz (then 8 MHz). Counted from the KiCad layouts of 103 open source designs using the ATmega328P-A.
What pull-up resistor is used on the ATmega328P-A RESET/PC6 pin?
The RESET/PC6 pin has a pull-up to 5V on 87 of 102 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 103 open source designs using the ATmega328P-A.
What parts are used alongside the ATmega328P-A?
The FT232RL, CH340C, AMS1117-5.0, AMS1117-3.3 and CH340G appear in the most repositories here.
Which microcontrollers do boards using the ATmega328P-A use?
Most are built on AVR/Arduino (125), ESP8266 (3), Microchip SAM (3) and RP2040/RP2350 (1).
How big is a typical board using the ATmega328P-A?
The median is 60 × 59.4 mm, and 83% are two-layer designs.
What is the most popular open source board using the ATmega328P-A?
By GitHub stars, Easyduino Atmega by Hanqaqa, with 754 stars.
Can I simulate one of these boards using the ATmega328P-A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.