UART-2-RS-485
Evans-Kwashie·UART-2-RS-485-PCB
About the UART-2-RS-485 PCB
UART-2-RS-485 is an open source PCB design by Evans-Kwashie, published on GitHub under the CERN-OHL-S-2.0 license. It is a 4-layer board measuring 23 × 56 mm, with 5 components from 4 distinct parts.
By type, the board carries 2 capacitors and 2 resistors.
It belongs with the rf & radio designs in this gallery.
From the project
UART to RS-485 converter board using the STR485 transceiver, DE/RE tied to a single direction-control pin, 120Ω bus termination, TVS protection on the A/B lines and differential pair routing. KiCad source, schematic PDF and 3D render. Not yet fabricated.
A 2-layer PCB that converts UART (TTL logic level) to RS-485 differential signaling, designed and routed from scratch in KiCad as a self-directed learning project focused on differential pair fundamentals.
RS-485 is widely used in industrial automation, building automation, and long-distance serial communication where noise immunity and cable length matter more than raw speed. This board bridges a standard UART interface (TX/RX) to an RS-485 A/B differential bus using the STR485 transceiver.

UART-2-RS-485 bill of materials (BOM)
5 components, 4 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STR485 | DFN-10-1EP_3x3mm_P0.5mm_EP1.646x3.1mm | STR 485 |
| 2 | 100nF | C_Disc_D4.3mm_W1.9mm_P5.00mm | C1, C2 |
| 1 | 10K | R_Axial_DIN0411_L9.9mm_D3.6mm_P12.70mm_Horizontal | R1 |
| 1 | 120 | R_Axial_DIN0411_L9.9mm_D3.6mm_P12.70mm_Horizontal | R2 |
UART-2-RS-485 design files
The KiCad project lives in the Evans-Kwashie/UART-2-RS-485-PCB repository on GitHub; these links point at the commit this page was built from.
- LayoutRS 485.kicad_pcb
- SchematicRS 485.kicad_sch
UART-2-RS-485: common questions
How big is the UART-2-RS-485 PCB?
The UART-2-RS-485 measures 23 × 56 mm, has 4 copper layers and is 1.600198 mm thick.
How many components are on the UART-2-RS-485?
5 components, from 4 distinct parts. The full bill of materials is listed on this page.
Where can I download the UART-2-RS-485 design files?
From the Evans-Kwashie/UART-2-RS-485-PCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the UART-2-RS-485 design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which Evans-Kwashie chose for the repository.
Similar boards
Hat
pa3gsb
65 × 56 mm81 parts2LNo license675Radioberry juice
pa3gsb
65 × 56 mm87 parts2LNo license675Radioberry preamp
pa3gsb
65 × 56 mm137 parts2LNo license675Goodwatch20
travisgoodspeed
25.6 × 27.6 mm20 parts2LNo license568GoodPocketWatch
travisgoodspeed
75.2 × 101.2 mm56 parts2LNo license568Goodwatch31
travisgoodspeed
25.6 × 27.6 mm23 parts2LNo license568