IllustraBot2
FablabLannion·IllustraBot2·Kicad/V2/Illustrabot2_IF_Motor_Beagle_v2.kicad_pcb
About the IllustraBot2 PCB
IllustraBot2 is an open source PCB design by FablabLannion, published on GitHub under the GPL-2.0 license. It is a 2-layer board measuring 230.5 × 158.8 mm, with 79 components from 14 distinct parts.
Other key parts include the STEPSTICK. By type, the board carries 24 resistors, 20 capacitors, 16 connectors, 6 ICs, 6 transistors and 6 diodes.
It belongs with the robotics & motion designs in this gallery, and the repository also holds 1 earlier revision of it.
From the project
2nd IllustraBot
This is a Fablab Lannion project. Purpose is to control a robotic arm over 4G using movments from an android phone.
List of directories : DOC : documentation (datasheets, ...) Kicad : electronic scheme android : well, android application beaglebone : soft running on the arm control platform
Main components on the IllustraBot2
IllustraBot2 bill of materials (BOM)
79 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 6 | STEPSTICK | Stepstick_footprint | U1, U2, U3, U4, U5, U6 |
| 6 | NPN | TO92 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 10 | CONN_4 | bornier4 | P1, P2, P3, P4, P5, P6, P7, P10 +2 |
| 2 | CONN_23X2 | SIL-2x23-v1 | P8, P9 |
| 4 | CONN_1 | 1pin | P13, P14, P15, P16 |
| 1 | JUMPER3 | SIL-3 | JP1 |
| 6 | LED | LED-3MM | D1, D2, D3, D4, D5, D6 |
| 6 | 100uF | CP4 | C1, C2, C7, C8, C11, C12 |
| 8 | 10uF | C1 | C3, C4, C15, C16, C17, C18, C19, C20 |
| 6 | 100nF | C1 | C5, C6, C9, C10, C13, C14 |
| 6 | 10kohm | R3 | R1, R2, R3, R4, R10, R12 |
| 6 | 150ohm | R3 | R5, R7, R9, R13, R15, R17 |
| 6 | 82kohm | R3 | R6, R8, R11, R14, R16, R18 |
| 6 | 47k | R3 | R19, R20, R21, R22, R23, R24 |
IllustraBot2 design files
The KiCad project lives in the FablabLannion/IllustraBot2 repository on GitHub; these links point at the commit this page was built from.
IllustraBot2: common questions
How big is the IllustraBot2 PCB?
The IllustraBot2 measures 230.5 × 158.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the IllustraBot2?
79 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the IllustraBot2 design files?
From the FablabLannion/IllustraBot2 repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the IllustraBot2 design in my own project?
Yes, under the terms of its GPL-2.0 license, which FablabLannion chose for the repository.
Earlier revisions in the repo: Illustrabot2_IF_Motor_Beagle_v1
Similar boards
Stack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kCube batteryboard
willem-pennings
95 × 95 mm4 parts2LGPL-3.01.1kTrollerv2
rene-dev
100 × 75 mm33 parts4LGPL-3.0979Powerstep
rene-dev
95.2 × 71.5 mm28 parts4LGPL-3.097911ua
rene-dev
57.3 × 19 mm26 parts2LGPL-3.0979Diff driver
rene-dev
32 × 22 mm14 parts2LGPL-3.0979