MetaForge
FidelOdok·MetaForge·examples/drone_flight_controller/drone-fc.kicad_sch
About the MetaForge PCB
MetaForge is an open source STM32 PCB design by FidelOdok, published on GitHub under the Apache-2.0 license. It is a board, with 9 components from 7 distinct parts.
Its main chip is the STM32F405RGT6, from the STM32 family. Other key parts include the MPU6050 and AMS1117-3.3. By type, the board carries 4 capacitors, 3 ICs and 2 resistors.
It belongs with the robotics & motion and sensors designs in this gallery.
From the project
AI Engineering Agent
This example demonstrates MetaForge's end-to-end hardware design validation pipeline using a realistic drone flight controller as the reference project. It exercises the complete stack from human intent (PRD) through Digital Twin, domain agents, skills, MCP protocol, and tool adapters.
The drone flight controller is a 4-layer PCB built around the STM32F405RGT6 MCU with an MPU6050 IMU, BMP280 barometer, GPS module, and motor driver FETs. This example shows how MetaForge validates the design across six engineering disciplines simultaneously, identifies supply chain risks, and tracks regulatory…
Main components on the MetaForge
MetaForge bill of materials (BOM)
9 components, 7 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F405RGT6 | U1 | |
| 1 | MPU6050 | U2 | |
| 1 | AMS1117-3.3 | U3 | |
| 1 | 100nF | C1 | |
| 2 | 10uF | C2, C3 | |
| 1 | 22uF | C4 | |
| 2 | 4.7k | R1, R2 |
MetaForge design files
The KiCad project lives in the FidelOdok/MetaForge repository on GitHub; these links point at the commit this page was built from.
MetaForge: common questions
What microcontroller does the MetaForge use?
The MetaForge is built around the STM32F405RGT6, from the STM32 family.
How many components are on the MetaForge?
9 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the MetaForge design files?
From the FidelOdok/MetaForge repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the MetaForge design in my own project?
Yes, under the terms of its Apache-2.0 license, which FidelOdok chose for the repository.
Can I test firmware for the MetaForge without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k