CanSat2020
GJN-Aerospace·CanSat2020·Probe/Hardware/CanSat2020ProbeS/CanSat2020Probe.kicad_pcb
About the CanSat2020 PCB
CanSat2020 is an open source STM32 PCB design by GJN-Aerospace, published on GitHub. It is a 2-layer board measuring 56 × 56 mm, with 35 components from 23 distinct parts.
Its main chip is the STM32F411RETx, from the STM32 family. Other key parts include the TESEO-LIV3F, RFM69W and LD3985M33R_SOT23. By type, the board carries 11 capacitors, 8 connectors, 6 resistors, 4 ICs, 4 diodes and 1 crystal.
From the project
CanSat 2020
GitHub repository for CanSat 2020 competitoin. You can find here a design of our CanSat probe PKII but also our Arduino code for openCanSat kit.
We designed our own probe. It name is "Cosmic Song II" or for short just CSII (in czech Píseň kosmická II, PKII). But we have in Software section a code for our backup probe from openCanSat kit.
We use as a our Ground Station a baseStation from openCanSat kit. So you can find in Software folder our code for it.

Main components on the CanSat2020
CanSat2020 bill of materials (BOM)
35 components, 23 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TESEO-LIV3F | SON110P970X1010X230-18N | IC1 |
| 1 | STM32F411RETx | LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | RFM69W | HOPERF_RFM69HW | U2 |
| 1 | LD3985M33R_SOT23 | SOT-23-5_HandSoldering | U3 |
| 1 | Crystal | Crystal_SMD_HC49-SD | Y1 |
| 1 | BME280 | BME280 | J1 |
| 1 | MPU-9250 | MPU-9250-4pin | J2 |
| 1 | Micro_SD_Card | microSD_HC_Wuerth_693072010801 | J3 |
| 1 | Conn_01x03_Male | Batt_PHS_Hor_Long18mm | J4 |
| 2 | Conn_Coaxial | U.FL_Hirose_U.FL-R-SMT-1_Vertical | J5, J6 |
| 1 | Conn_01x06_Male | PinHeader_1x06_P2.54mm_Vertical | J7 |
| 1 | Conn_01x03_Male | PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | SW_DIP_x01 | Sw_ESP2010 | SW1 |
| 3 | LED | LED_1206_3216Metric | D1, D2, D3 |
| 1 | D | D_DO-41_SOD81_P10.16mm_Horizontal | D4 |
| 5 | 100nF | C_0805_2012Metric | C1, C4, C5, C6, C7 |
| 2 | 15pF | C_0805_2012Metric | C2, C3 |
| 2 | 47uF | CP_Radial_D5.0mm_P2.00mm | C8, C10 |
| 1 | 10nF | C_0805_2012Metric | C9 |
| 1 | 4.7uF | C_0805_2012Metric | C11 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 10k | R_0805_2012Metric | R1, R2 |
| 3 | R | R_0805_2012Metric | R3, R4, R5 |
| 1 | 100k | R_0805_2012Metric | R6 |
CanSat2020 design files
The KiCad project lives in the GJN-Aerospace/CanSat2020 repository on GitHub; these links point at the commit this page was built from.
CanSat2020: common questions
What microcontroller does the CanSat2020 use?
The CanSat2020 is built around the STM32F411RETx, from the STM32 family.
How big is the CanSat2020 PCB?
The CanSat2020 measures 56 × 56 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the CanSat2020?
35 components, from 23 distinct parts. The full bill of materials is listed on this page.
Where can I download the CanSat2020 design files?
From the GJN-Aerospace/CanSat2020 repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the CanSat2020 design in my own project?
The repository has no license, so all rights stay with GJN-Aerospace. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the CanSat2020 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k