HardLabs

Graduation Project

hamzaaldabe·Graduation_Project·FC_V1/FC_V1.kicad_pcb

Graduation Project PCB layout, top view — open source STM32 board by hamzaaldabe

About the Graduation Project PCB

Graduation Project is an open source STM32 PCB design by hamzaaldabe, published on GitHub. It is a 4-layer board measuring 72.7 × 73.3 mm, with 41 components from 18 distinct parts.

Its main chip is the STM32F415RGTx, from the STM32 family. Other key parts include the NCP1117-3.3_TO252, MPU-6000 and NCP1117-5.0_TO252. By type, the board carries 15 capacitors, 5 connectors, 5 resistors, 4 ICs, 3 diodes and 1 crystal.

Main components on the Graduation Project

NCP1117-3.3_TO252MPU-6000STM32F415RGTxNCP1117-5.0_TO252

Graduation Project bill of materials (BOM)

41 components, 18 distinct parts.

QtyPartRefs
1
NCP1117-3.3_TO252
U1
1
MPU-6000
U2
1
STM32F415RGTx
U3
1
NCP1117-5.0_TO252
U4
1
8MHZ
Y1
1
USB_B_Micro
J1
4
Conn_01x04_Male
J2, J3, J4, J5
3
10Kohm
R_BOOT0, R_BOOT1, R_RESET1
2
1Kohm
R_LED1, R_LED2
3
SW_Push
SW_BOOT0, SW_BOOT1, SW_RESET1
1
BAT54C
D1
2
LED
D2, D3
3
0.1uf
C1_IMU1, C1_RESET1, C3_IMU1
7
100nf
C1_VCAP1, C1_VDD1, C2_VCAP1, C2_VDD1, C3_VDD1, C4_VDD1, C5_VDD1
4
10uf
C1_VIN1, C1_VREG1, C2_VIN1, C2_VREG1
1
2.2uf
C2_IMU1
3
10Kohm
R1_IMU1, R3_USB1, R4_USB1
2
22ohm
R1_USB1, R2_USB1

Graduation Project design files

The KiCad project lives in the hamzaaldabe/Graduation_Project repository on GitHub; these links point at the commit this page was built from.

Graduation Project: common questions

What microcontroller does the Graduation Project use?

The Graduation Project is built around the STM32F415RGTx, from the STM32 family.

How big is the Graduation Project PCB?

The Graduation Project measures 72.7 × 73.3 mm, has 4 copper layers and is 4.69 mm thick.

How many components are on the Graduation Project?

41 components, from 18 distinct parts. The full bill of materials is listed on this page.

Where can I download the Graduation Project design files?

From the hamzaaldabe/Graduation_Project repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Graduation Project design in my own project?

The repository has no license, so all rights stay with hamzaaldabe. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Graduation Project without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards