CADFiles
hashaam1217·CADFiles
About the CADFiles PCB
CADFiles is an open source STM32 PCB design by hashaam1217, published on GitHub. It is a board, with 55 components from 23 distinct parts.
Its main chip is the STM32H753ZIT6, from the STM32 family. Other key parts include the AMS1117-3.3 and USBLC6-2SC6. By type, the board carries 24 capacitors, 14 resistors, 5 connectors, 3 ICs, 2 crystals and 1 switch.
Main components on the CADFiles
CADFiles bill of materials (BOM)
55 components, 23 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32H753ZIT6 | LQFP-144_20x20mm_P0.5mm | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U3 |
| 1 | 25MHZ | Y1 | |
| 1 | 32.67 KHz | Y2 | |
| 1 | USB_C_Receptacle_USB2.0 | J1 | |
| 4 | Conn_01x15_Pin | J6, J7, J8, J9 | |
| 4 | MountingHole | H1, H2, H3, H4 | |
| 1 | SW_SPDT | SW1 | |
| 1 | Red | D1 | |
| 1 | 120R | FB1 | |
| 14 | 100n | C1, C2, C3, C4, C5, C6, C7, C8 +6 | |
| 2 | 1u | C13, C21 | |
| 2 | 0.2u | C15, C16 | |
| 1 | 10u | C17 | |
| 1 | 22u | C18 | |
| 2 | 14p | C19, C20 | |
| 2 | 22p | C23, C24 | |
| 2 | 10K | R1, R5 | |
| 2 | 5.1K | R2, R3 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1K | R4 | |
| 1 | 100K | R6 | |
| 8 | 4.7K | R7, R8, R9, R10, R11, R12, R13, R14 |
CADFiles design files
The KiCad project lives in the hashaam1217/CADFiles repository on GitHub; these links point at the commit this page was built from.
- SchematicAS_FlightController.kicad_sch
CADFiles: common questions
What microcontroller does the CADFiles use?
The CADFiles is built around the STM32H753ZIT6, from the STM32 family.
How many components are on the CADFiles?
55 components, from 23 distinct parts. The full bill of materials is listed on this page.
Where can I download the CADFiles design files?
From the hashaam1217/CADFiles repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the CADFiles design in my own project?
The repository has no license, so all rights stay with hashaam1217. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the CADFiles without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k