Kestrel esc
HeyPCB·kestrel-esc·kicad/kestrel_esc.kicad_pcb
About the Kestrel esc PCB
Kestrel esc is an open source STM32 PCB design by HeyPCB, published on GitHub under the CERN-OHL-S-2.0 license. It is a 6-layer board measuring 48 × 52 mm, with 160 components from 26 distinct parts.
Its main chip is the STM32G071G8U6N, from the STM32 family. Other key parts include the LM5109BSD/NOPB, INA180A2IDBVR, LMR51430YFDDCR and L78L33ABUTR. By type, the board carries 52 capacitors, 50 resistors, 24 transistors, 19 ICs, 12 test points and 1 connector.
It belongs with the robotics & motion and power & battery designs in this gallery.
From the project
Kestrel 4in1: 6S 4-in-1 ESC running stock AM32 on four STM32G071s, with 24 CSD18540 FETs, LM5109B drivers and battery current sensing. 48 x 52 mm 6-layer KiCad 10 board, DRC clean, with gerbers, BOM, CPL and STEP.
Four STM32G071s running stock AM32, twelve half-bridge drivers and twenty-four 60 V FETs stacked through a 48 x 52 mm board, with battery current sensing for the flight controller.
The Kestrel 4in1 is the ESC of Kestrel. Each motor has its own STM32G071 wired to AM32's HARDWAREGROUPG0H pin map, the group of the Mamba F55 G071 build, so it runs a stock AM32 release: firmware/am32/README.md` maps every pin and walks through the first flash. Each half bridge is stacked through the board, the high-side FET on the top face over its low side on the bottom, joined by the motor wire soldered through…

Main components on the Kestrel esc
Kestrel esc bill of materials (BOM)
160 components, 26 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 12 | LM5109BSD/NOPB LM5109B | WSON-8-1EP_4x4mm_P0.8mm_EP2.6x3mm | U1, U2, U3, U5, U6, U7, U9, U10 +4 |
| 4 | STM32G071G8U6N | QFN-28_4x4mm_P0.5mm | U4, U8, U12, U16 |
| 1 | INA180A2IDBVR INA180A2 | SOT-23-5 | U17 |
| 1 | LMR51430YFDDCR LMR51430YF | SOT-23-6 | U18 |
| 1 | L78L33ABUTR L78L33 | SOT-89-3 | U19 |
| 24 | CSD18540Q5B | TDSON-8-1 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 +16 |
| 1 | SM08B-SRSS-TB(LF)(SN) ESC | JST_SH_SM08B-SRSS-TB_1x08-1MP_P1.00mm_Horizontal | J1 |
| 12 | motor | TestPoint_THTPad_3.0x3.0mm_Drill1.5mm | TP1, TP2, TP3, TP6, TP7, TP8, TP11, TP12 +4 |
| 1 | SMAJ30A | D_SMA | D1 |
| 1 | SWPA5040S6R8MT 6.8uH | L_Sunlord_SWPA5040S | L1 |
| 13 | CL05A105KA5NQNC 1uF | C_0402_1005Metric | C1, C3, C5, C10, C12, C14, C19, C21 +5 |
| 13 | CL05B104KB54PNC 100nF | C_0402_1005Metric | C2, C4, C6, C11, C13, C15, C20, C22 +5 |
| 11 | CL05B104KO5NNNC 100nF | C_0402_1005Metric | C7, C9, C16, C18, C25, C27, C34, C36 +3 |
| 4 | CL10A475KO8NNNC 4.7uF | C_0603_1608Metric | C8, C17, C26, C35 |
| 6 | CL31A106KBHNNNE 10uF | C_1206_3216Metric | C37, C38, C39, C40, C41, C42 |
| 4 | GRM21BR61H106KE43L 10uF | C_0805_2012Metric | C45, C48, C49, C50 |
| 1 | CL10A105KB8NNNC 1uF | C_0603_1608Metric | C51 |
| 4 | 0402WGF1000TCE 100 | R_0402_1005Metric | R1, R12, R23, R34 |
| 24 | 0402WGF2002TCE 20k | R_0402_1005Metric | R2, R3, R4, R8, R9, R10, R13, R14 +16 |
| 12 | 0402WGF2201TCE 2.2k | R_0402_1005Metric | R5, R6, R7, R16, R17, R18, R27, R28 +4 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 0402WGF7500TCE 750 | R_0402_1005Metric | R11, R22, R33, R44 |
| 2 | RE2512F3R0R5L 0.5m | R_2512_6332Metric | R45, R46 |
| 1 | 0402WGF1002TCE 10k | R_0402_1005Metric | R47 |
| 1 | 0402WGF1001TCE 1k | R_0402_1005Metric | R48 |
| 1 | 0603WAF1003T5E 100k | R_0603_1608Metric | R49 |
| 1 | 0603WAF6491T5E 6.49k | R_0603_1608Metric | R50 |
Kestrel esc design files
The KiCad project lives in the HeyPCB/kestrel-esc repository on GitHub; these links point at the commit this page was built from.
Kestrel esc: common questions
What microcontroller does the Kestrel esc use?
The Kestrel esc is built around the STM32G071G8U6N, from the STM32 family.
How big is the Kestrel esc PCB?
The Kestrel esc measures 48 × 52 mm, has 6 copper layers and is 1.6 mm thick.
How many components are on the Kestrel esc?
160 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Kestrel esc design files?
From the HeyPCB/kestrel-esc repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Kestrel esc design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which HeyPCB chose for the repository.
Can I test firmware for the Kestrel esc without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k