14 open source boards using the INA180A2IDBVR

Real designs built with the INA180A2IDBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

14 boardsClear filters|Most starred

How designs wire the INA180A2IDBVR

Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the INA180A2IDBVR connects to, and the resistors, capacitors and other passives placed on it.

  • The VS pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 10 nF).
  • The OUT pin has a series resistor on 8 of 11 designs, most often 10 kΩ (then 33 kΩ).
OUTpin 1Connected to: The microcontroller 36%
  • Series resistor on 73% · 10 kΩ (2), 33 kΩ (2), 1 kΩ (2)
GNDpin 2Connected to: GND 91%
VSpin 5Connected to: 3.3V 82% · a signal 18%
  • Decoupling capacitor on 82% · 100 nF (15), 10 nF (4)

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include RPI CMx Carrier by lecejeff, Thermal spectrum by spbnick, 5S-Blower-Controller by 10htts and Nylok-Heater by 3nboyd.

The INA180A2IDBVR in open source designs

The gallery holds 14 open source boards using the INA180A2IDBVR from 14 GitHub repositories; a typical one measures about 80 × 100 mm and carries around 64 components.

55% are two-layer designs, the rest use four layers or more, and 64% carry an open source license.

The most starred is RPI CMx Carrier by lecejeff.

Microcontrollers on boards using the INA180A2IDBVR

INA180A2IDBVR: common questions

Where can I find a INA180A2IDBVR reference design?

Each of the 14 boards on this page is a real design using the INA180A2IDBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the INA180A2IDBVR VS pin?

The VS pin has a decoupling capacitor on 9 of 11 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 11 open source designs using the INA180A2IDBVR.

What resistor goes on the INA180A2IDBVR OUT pin?

The OUT pin has a series resistor on 8 of 11 designs, most often 10 kΩ (then 33 kΩ). Counted from the KiCad layouts of 11 open source designs using the INA180A2IDBVR.

What parts are used alongside the INA180A2IDBVR?

The 74LVC1G08 (TBD), AP7381-33Y-13, LM393DR (1/2), MCP4725A0T-E/CH and MP8771GQ-Z appear in the most repositories here.

Which microcontrollers do boards using the INA180A2IDBVR use?

Most are built on STM32 (5), PIC (2), AVR/Arduino (1) and WCH CH32/CH55x (1).

How big is a typical board using the INA180A2IDBVR?

The median is 80 × 100 mm, and 55% are two-layer designs.

What is the most popular open source board using the INA180A2IDBVR?

By GitHub stars, RPI CMx Carrier by lecejeff, with 26 stars.

Can I simulate one of these boards using the INA180A2IDBVR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part