Pomodoro pal

HeyPCB·pomodoro-pal·kicad/pomodoro_pal.kicad_pcb

Pomodoro pal PCB layout, top view — open source RISC-V board by HeyPCB

About the Pomodoro pal PCB

Pomodoro pal is an open source RISC-V PCB design by HeyPCB, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 69.6 × 66.4 mm, with 37 components from 10 distinct parts.

Its main chip is the CH32V003F4P6, from the RISC-V family. By type, the board carries 18 resistors, 14 diodes, 2 capacitors, 1 IC, 1 connector and 1 buzzer.

From the project

Pomodoro Pal: A tomato on your desk that keeps you focused for 25 minutes, without your phone. KiCad 10, heypcb.ai merch.

A tomato on your desk that keeps you focused for 25 minutes, without your phone.

Pomodoro Pal is a tomato-shaped Pomodoro timer that lies flat on your desk, powered over USB-C. Tap the gold pad in its calyx to start a 25-minute focus session: twelve red LEDs around its face go out one by one, clockwise, and the next one to go out breathes. At the end it chirps softly and its two green leaf tips glow through a 5-minute break (15 minutes after every fourth session).

Pomodoro pal, from the project README
From the project README

Main components on the Pomodoro pal

Pomodoro pal bill of materials (BOM)

37 components, 10 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
CH32V003F4P6
U1
1
TYPE-C-31-M-12
USB-C
J1
1
PKMCS0909E4000-R1
PKMCS0909E4000
BZ1
2
KT-0603G
Green
D1, D2
12
KT-0603R
Red
D3, D4, D5, D6, D7, D8, D9, D10 +4
1
CL21A106KAYNNNE
10uF
C1
1
CC0603KRX7R9BB104
100nF
C2
2
0402WGF5101TCE
5.1k
R1, R2
15
0603WAF1001T5E
1k
R3, R5, R6, R7, R8, R9, R10, R11 +7
1
0603WAF1000T5E
100
R4

Pomodoro pal design files

The KiCad project lives in the HeyPCB/pomodoro-pal repository on GitHub; these links point at the commit this page was built from.

Pomodoro pal: common questions

What microcontroller does the Pomodoro pal use?

The Pomodoro pal is built around the CH32V003F4P6, from the RISC-V family.

How big is the Pomodoro pal PCB?

The Pomodoro pal measures 69.6 × 66.4 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Pomodoro pal?

37 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Pomodoro pal design files?

From the HeyPCB/pomodoro-pal repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Pomodoro pal design in my own project?

Yes, under the terms of its CERN-OHL-S-2.0 license, which HeyPCB chose for the repository.

Can I test firmware for the Pomodoro pal without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RISC-V firmware against it before you order a PCB.

Similar boards