Stm8s triac contoller

hwwong·stm8s-triac-controller

Stm8s triac contoller PCB layout, top view — open source STM32 board by hwwong

About the Stm8s triac contoller PCB

Stm8s triac contoller is an open source STM32 PCB design by hwwong, published on GitHub under the MIT license. It is a 2-layer board measuring 31.5 × 44.7 mm, with 44 components from 32 distinct parts.

Its main chip is the STM8S003F3P, from the STM32 family. Other key parts include the EL357N and TRIAC T435-600T1. By type, the board carries 16 resistors, 8 connectors, 8 capacitors, 4 ICs, 3 diodes and 2 transistors.

Main components on the Stm8s triac contoller

STM8S003F3PEL357NTRIAC T435-600T1

Stm8s triac contoller bill of materials (BOM)

44 components, 32 distinct parts.

QtyPartRefs
1
STM8S003F3P
IC1
2
EL357N
U1, U2
1
TRIAC T435-600T1
U3
1
IR-Receiver
Q1
1
BC847
Q2
1
ST-Link-V2
J1
1
Solder-Jumper-2
J2
1
UART
P1
1
LOAD
P2
1
LIVE
P3
2
NEUTRAL
P4, P5
1
+5V Power
P6
1
Key1
SW1
1
Key2
SW2
1
PT100
TH1
1
Led_Small
D1
1
5.6V/0.5W
D2
1
LL4148
D3
1
470nF
C1
4
100nF
C2, C3, C5, C8
Show 12 more
QtyPartRefs
1
470nF/400V
C4
1
100pF
C6
1
470uF/16V
C7
4
100
R1, R2, R3, R5
3
1K
R4, R7, R8
2
560
R6, R9
1
2.7K
R10
1
100K
R11
1
470/1W
R12
2
4.7K
R13, R16
1
47
R14
1
330K/0.5W
R15

Stm8s triac contoller design files

The KiCad project lives in the hwwong/stm8s-triac-controller repository on GitHub; these links point at the commit this page was built from.

Stm8s triac contoller: common questions

What microcontroller does the Stm8s triac contoller use?

The Stm8s triac contoller is built around the STM8S003F3P, from the STM32 family.

How big is the Stm8s triac contoller PCB?

The Stm8s triac contoller measures 31.5 × 44.7 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Stm8s triac contoller?

44 components, from 32 distinct parts. The full bill of materials is listed on this page.

Where can I download the Stm8s triac contoller design files?

From the hwwong/stm8s-triac-controller repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the Stm8s triac contoller design in my own project?

Yes, under the terms of its MIT license, which hwwong chose for the repository.

Can I test firmware for the Stm8s triac contoller without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in stm8s-triac-controller

Similar boards