Stm8s triac contoller panel
hwwong·stm8s-triac-controller
About the Stm8s triac contoller panel PCB
Stm8s triac contoller panel is an open source STM32 PCB design by hwwong, published on GitHub under the MIT license. It is a 2-layer board measuring 94.5 × 89.4 mm, with 44 components from 32 distinct parts.
Its main chip is the STM8S003F3P, from the STM32 family. Other key parts include the EL357N and TRIAC T435-600T1. By type, the board carries 16 resistors, 8 connectors, 8 capacitors, 4 ICs, 3 diodes and 2 transistors.
Main components on the Stm8s triac contoller panel
Stm8s triac contoller panel bill of materials (BOM)
44 components, 32 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM8S003F3P | TSSOP-20_4.4x6.5mm_Pitch0.65mm | IC1 |
| 2 | EL357N | Optocoupler_SMD_HandSoldering_KPC357_LTV35x_PC357_SingleChannel | U1, U2 |
| 1 | TRIAC T435-600T1 | TO-220_Neutral123_Vertical_LargePads | U3 |
| 1 | IR-Receiver | PNA460XM | Q1 |
| 1 | BC847 | SOT-23 | Q2 |
| 1 | ST-Link-V2 | Pin_Header_Straight_1x04 | J1 |
| 1 | Solder-Jumper-2 | PAD-JUMPER-2-NO_YES_SILK | J2 |
| 1 | UART | Pin_Header_Straight_1x04 | P1 |
| 1 | LOAD | SolderWirePad_single_1-2mmDrill | P2 |
| 1 | LIVE | SolderWirePad_single_1-2mmDrill | P3 |
| 2 | NEUTRAL | SolderWirePad_single_1-2mmDrill | P4, P5 |
| 1 | +5V Power | Pin_Header_Straight_1x02 | P6 |
| 1 | Key1 | TACTILE-PTH | SW1 |
| 1 | Key2 | TACTILE-PTH | SW2 |
| 1 | PT100 | TerminalBlock_Pheonix_MKDS1.5-3pol | TH1 |
| 1 | Led_Small | LED-3MM | D1 |
| 1 | 5.6V/0.5W | SOD-80 | D2 |
| 1 | LL4148 | SOD-80 | D3 |
| 1 | 470nF | C_0805 | C1 |
| 4 | 100nF | C_0805 | C2, C3, C5, C8 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 470nF/400V | C_Rect_L18_W11_H19_P15 | C4 |
| 1 | 100pF | C_0805 | C6 |
| 1 | 470uF/16V | C_Radial_D8_L11.5_P3.5 | C7 |
| 4 | 100 | R_0805 | R1, R2, R3, R5 |
| 3 | 1K | R_0805 | R4, R7, R8 |
| 2 | 560 | R_0805 | R6, R9 |
| 1 | 2.7K | R_0805 | R10 |
| 1 | 100K | R_0805 | R11 |
| 1 | 470/1W | Resistor_Vertical_RM5mm | R12 |
| 2 | 4.7K | R_0805 | R13, R16 |
| 1 | 47 | R_0805 | R14 |
| 1 | 330K/0.5W | Resistor_Horizontal_RM10mm | R15 |
Stm8s triac contoller panel design files
The KiCad project lives in the hwwong/stm8s-triac-controller repository on GitHub; these links point at the commit this page was built from.
Stm8s triac contoller panel: common questions
What microcontroller does the Stm8s triac contoller panel use?
The Stm8s triac contoller panel is built around the STM8S003F3P, from the STM32 family.
How big is the Stm8s triac contoller panel PCB?
The Stm8s triac contoller panel measures 94.5 × 89.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Stm8s triac contoller panel?
44 components, from 32 distinct parts. The full bill of materials is listed on this page.
Where can I download the Stm8s triac contoller panel design files?
From the hwwong/stm8s-triac-controller repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Stm8s triac contoller panel design in my own project?
Yes, under the terms of its MIT license, which hwwong chose for the repository.
Can I test firmware for the Stm8s triac contoller panel without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in stm8s-triac-controller
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k