Delta-Printer
Icyconfusion·Delta-Printer·PCB/Delta 3d printer.kicad_sch
About the Delta-Printer PCB
Delta-Printer is an open source STM32 PCB design by Icyconfusion, published on GitHub. It is a board, with 59 components from 34 distinct parts.
Its main chip is the STM32F407VGTx, from the STM32 family. Other key parts include the MP1584EN and AP2112K-3.3. By type, the board carries 25 capacitors, 17 resistors, 8 connectors, 3 ICs, 2 inductors and 1 crystal.
From the project
An STM32 based delta style 3D printer running Marlin firmware
Note to reviewer: My JLCPCB/MC screenshot is inclusive of tax and cheapest shipping option, it went into my "orders" tab despite not being paid for, but that is the total price, and the checkout page. Thank you:)
400mm MGN12H linear rails are mounted to the inside profile of each tower using M3x8 screws.
To mount the NEMA17 stepper motors, the motors are screwed into the mount bracket, which attaches to the inside of the two bottom triangles.
Main components on the Delta-Printer
Delta-Printer bill of materials (BOM)
59 components, 34 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F407VGTx | LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | MP1584EN | SOIC127P600X170-9N | U6 |
| 1 | AP2112K-3.3 | SOT-23-5_HandSoldering | U7 |
| 1 | Crystal_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 2 | Conn_02x05_Odd_Even | IDC-Header_2x05_P2.54mm_Vertical | J7, J17 |
| 2 | Conn_01x02 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J11, J12 |
| 1 | Conn_02x07_Odd_Even | PinHeader_2x07_P2.54mm_Vertical | J13 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J14 |
| 1 | Conn_01x05 | PinHeader_1x05_P2.54mm_Vertical | J15 |
| 1 | Screw_Terminal_01x02 | Wuerth_691311400102_P7.62mm | J16 |
| 1 | Fuse | Fuse_Holder_KCD3_Medium | F1 |
| 1 | SW_Push | SW_TS-1088-AR02016 | SW1 |
| 1 | SS34 | D_SMA_Handsoldering | D1 |
| 1 | FerriteBead | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | FB1 |
| 1 | 10uH | L_6.3x6.3_H3 | L1 |
| 4 | 1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C29, C38, C49, C50 |
| 9 | 100 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C30, C31, C32, C33, C34, C35, C39, C40 +1 |
| 2 | 18pf | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C36, C37 |
| 2 | 22uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C42, C47 |
| 1 | 10uf 50v | CP_Elec_5x5.4 | C43 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 220pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C44 |
| 2 | C | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C45, C51 |
| 1 | 47-100uF Electrolytic | C_Elec_6.3x7.7 | C46 |
| 1 | 100uF electrolytic | C_Elec_6.3x7.7 | C48 |
| 2 | 2.2uF ceramic - low ESR | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C52, C53 |
| 5 | R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R25, R26, R27, R28, R38 |
| 2 | 5.1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R29, R30 |
| 3 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R31, R33, R35 |
| 1 | 33 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R32 |
| 1 | 52.3k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R34 |
| 1 | 100k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R36 |
| 1 | 24.9k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R37 |
| 1 | 68.1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R39 |
| 2 | 22 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R40, R41 |
Delta-Printer design files
The KiCad project lives in the Icyconfusion/Delta-Printer repository on GitHub; these links point at the commit this page was built from.
- SchematicPCB/Delta 3d printer.kicad_sch
- BOMBOM.csv
Delta-Printer: common questions
What microcontroller does the Delta-Printer use?
The Delta-Printer is built around the STM32F407VGTx, from the STM32 family.
How many components are on the Delta-Printer?
59 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Delta-Printer design files?
From the Icyconfusion/Delta-Printer repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Delta-Printer design in my own project?
The repository has no license, so all rights stay with Icyconfusion. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Delta-Printer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k