Flight computer v2

IshraqueSarwar·CORESEN-custom-flight-computer·schematics/version2/flight_computer_v2/flight_computer_v2.kicad_pcb

Flight computer v2 PCB layout, top view — open source STM32 board by IshraqueSarwar

About the Flight computer v2 PCB

Flight computer v2 is an open source STM32 PCB design by IshraqueSarwar, published on GitHub. It is a 2-layer board measuring 51 × 40 mm, with 50 components from 22 distinct parts.

Its main chip is the STM32F407VGTx, from the STM32 family. Other key parts include the MPU-9250, AMS1117-3.3 and AMS1117-5.0. By type, the board carries 25 capacitors, 8 resistors, 6 connectors, 4 ICs, 4 diodes and 1 crystal.

It belongs with the power & battery and sensors designs in this gallery.

From the project

Flight computer

A from-scratch, hand-soldered flight controller built to close the gap between writing embedded firmware and actually understanding the hardware it runs on.

CoreSen-V2, fully populated. LQFP-100 STM32F407VGT6, salvaged MPU-9250, hand-soldered in one four-hour session.

- Why This Board Exists - At a Glance - The Build Timelapse - System Architecture - Hardware Deep Dive - Microcontroller and Clocking - Power Tree - The IMU Problem: SPI vs I2C - USB and Programming - Decoupling Strategy - Peripheral and Pin Map - PCB Layout - Engineering Tradeoffs - Known Issues and V3 Roadmap - Bring-Up…

Flight computer v2, from the project README
From the project README

Main components on the Flight computer v2

Flight computer v2 bill of materials (BOM)

50 components, 22 distinct parts.

QtyPartRefs
1
STM32F407VGTx
U1
1
MPU-9250
U2
1
AMS1117-3.3
U3
1
AMS1117-5.0
U4
1
8MHz
Y1
3
Conn_01x04_Pin
J1, J2, J3
1
Conn_01x03_Pin
J4
1
USB_B_Micro
J5
1
Conn_01x05_Pin
J6
1
SW_Push
SW1
2
LED_Small
D1, D2
1
LED
D3
1
BAT54C
D5
1
120R
FB1
13
100n
C1, C2, C3, C4, C5, C6, C7, C12 +5
1
10u
C8
2
10n
C9, C18
3
1u
C10, C11, C20
2
10p
C15, C16
4
22u
C21, C22, C24, C25
Show 2 more
QtyPartRefs
5
10k
R1, R2, R3, R4, R5
3
1k
R8, R10, R11

Flight computer v2 design files

The KiCad project lives in the IshraqueSarwar/CORESEN-custom-flight-computer repository on GitHub; these links point at the commit this page was built from.

Flight computer v2: common questions

What microcontroller does the Flight computer v2 use?

The Flight computer v2 is built around the STM32F407VGTx, from the STM32 family.

How big is the Flight computer v2 PCB?

The Flight computer v2 measures 51 × 40 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Flight computer v2?

50 components, from 22 distinct parts. The full bill of materials is listed on this page.

Where can I download the Flight computer v2 design files?

From the IshraqueSarwar/CORESEN-custom-flight-computer repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Flight computer v2 design in my own project?

The repository has no license, so all rights stay with IshraqueSarwar. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Flight computer v2 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in CORESEN-custom-flight-computer

Similar boards