Exponential signal generator
jb-23·exponential-signal-generator·EE-Kicad/Exponential Generator Minimal.kicad_pcb
About the Exponential signal generator PCB
Exponential signal generator is an open source PCB design by jb-23, published on GitHub. It is a 2-layer board measuring 85 × 56 mm, with 59 components from 18 distinct parts.
Other key parts include the XC6902N501PR-G, CD4017 and TS27M2. By type, the board carries 40 resistors, 7 capacitors, 3 ICs, 3 test points, 2 diodes and 1 battery holder.
It belongs with the test & measurement designs in this gallery.
From the project
Electronic circuit to generate an exponentially rising test signal.
This circuit generates a fixed waveform of exponentially rising DC steps, which could be used for testing logarithmic amplifiers.
Output voltages range from 320 uV to 3.2V in steps with a ratio of 3.16, equivalent to a 10 dB change. The waveform repeats at a nominal 50 Hz to allow a flicker-free image on an analogue oscilloscope.
The PCB is designed to work as a naked board that sits on top of the 9V battery that powers it. The output pads are designed to accept the majority of 4mm binding posts and when unpopulated will also work with crocodile clips.

Main components on the Exponential signal generator
Exponential signal generator bill of materials (BOM)
59 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XC6902N501PR-G | SOT-89-3_Handsoldering | U1 |
| 1 | CD4017 | SOIC-16_3.9x9.9mm_P1.27mm | U3 |
| 1 | TS27M2 | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | 9V | BatteryHolder_PCB_PP3 | BT1 |
| 2 | 20k | Trimmer_Universal_3296_Horizontal | RV1, RV2 |
| 1 | DPDT On-On-On | Switch_Toggle_DPDT_RA_PCB | SW1 |
| 1 | Trigger | Binding_Post | TP1 |
| 1 | Output | Binding_Post | TP2 |
| 1 | Ground | Binding_Post | TP3 |
| 2 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2, D3 |
| 2 | 1 | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2 |
| 3 | .1 | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C3, C4, C5 |
| 2 | .0022 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7, C8 |
| 15 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R7, R8, R9, R10, R12, R14, R16 +7 |
| 12 | 14.7k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R11, R13, R15, R17, R19, R21, R23 +4 |
| 7 | 100k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4, R5, R6, R32, R34, R36 |
| 5 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R27, R28, R29, R30, R38 |
| 1 | 120 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R33 |
Exponential signal generator design files
The KiCad project lives in the jb-23/exponential-signal-generator repository on GitHub; these links point at the commit this page was built from.
Exponential signal generator: common questions
How big is the Exponential signal generator PCB?
The Exponential signal generator measures 85 × 56 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Exponential signal generator?
59 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the Exponential signal generator design files?
From the jb-23/exponential-signal-generator repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Exponential signal generator design in my own project?
The repository has no license, so all rights stay with jb-23. Use it as a reference, and ask the author before reusing the design.
Similar boards
AnalyzerBoxPCB fork
gusmanb
52.7 × 47.9 mm54 parts4LGPL-3.05.0kLevelShifter
gusmanb
28.3 × 39.8 mm21 parts2LGPL-3.05.0kStackLink
gusmanb
52.3 × 10.5 mm5 parts2LGPL-3.05.0kEleLab v2 Frontpanel a
Chrismettal
88 × 25 mm23 parts2LGPL-3.0528EleLab v2 Bus150
Chrismettal
150 × 50 mm37 parts2LGPL-3.0528EleLab v2 PowerFeed
Chrismettal
68 × 50 mm11 parts2LGPL-3.0528