Nabby linux
JoachimBose·nabby-linux·board/vuctf-revA/kicad_files/f1c200s_proj/f1c200s_proj.kicad_pcb
About the Nabby linux PCB
Nabby linux is an open source PCB design by JoachimBose, published on GitHub under the GPL-2.0 license. It is a 2-layer board measuring 80 × 80.5 mm, with 60 components from 29 distinct parts.
Other key parts include the F1C200S, AMS1117, TLV71311PDBVR and TLV70225DBVR. By type, the board carries 23 capacitors, 15 resistors, 11 test points, 6 ICs, 2 diodes and 1 crystal.
From the project
An Allwinner F1C100s / F1C200s buildroot external tree for (among others) the hardware challenge for VUCTF-2026
This will import all the files from this repository. If you are new to buildroot, consider taking a look around this repository to see what you just imported.
after you compiled your buildroot, you should get a flash.bin image as described in the genimage.cfg. To flash it, put the chip in FEL-mode. This is done by shorting chipselect of the spiflash to 3.3 volts and powering on the device, after powerup remove the short. Now you can use:

Main components on the Nabby linux
Nabby linux bill of materials (BOM)
60 components, 29 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | F1C200S f1c200s Allwinner(全志) | QFN-88_L10.0-W10.0-P0.40-BL-EP6.75_f1c200s | U1 |
| 1 | ~ XTX(芯天下) | FLASH-8pin | U2 |
| 2 | AMS1117 Advanced Monolithic Systems | SOT-223-3_L6.5-W3.4-P2.30-LS7.0-BR | U4, U5 |
| 1 | TLV71311PDBVR TI(德州仪器) | TI-LDO-1v1 | U6 |
| 1 | TLV70225DBVR TI(德州仪器) | TI-LDO-2v5 | U7 |
| 1 | X322524MOB4SI Yangxing Tech | OSC-SMD_4P-L3.2-W2.5-BL | X1 |
| 1 | Tactile Button, 160gf XUNPU | SW_TS-1088-AR02016 | S1_RST1 |
| 1 | +3v3 | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP1 |
| 1 | +1v1 | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP2 |
| 1 | +2v5 | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP3 |
| 1 | CS | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP4 |
| 1 | ETH_+3V3 eth_+3v3 | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP5 |
| 1 | GND | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP6 |
| 1 | PD3 | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP10 |
| 1 | PD4 | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP11 |
| 1 | LRADC0 | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP12 |
| 1 | PD5 | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP13 |
| 1 | PD6 | TestPoint_THTPad_2.0x2.0mm_Drill1.0mm | TP14 |
| 1 | USB-TYPE-C-020 DEALON(德艺隆) | USB-SMD_USB-TYPE-C-020 | USB1 |
| 2 | C2286 Red Hubei KENTO Elec | D_0603 | D1, D2 |
Show 9 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 18PF 18pF Samsung Electro-Mechanics | C_0603 | C1, C2, C19, C22 |
| 14 | 100NF 100nF Samsung Electro-Mechanics | C_0805 | C3, C4, C5, C6, C7, C8, C9, C10 +6 |
| 5 | 1UF 1uF Samsung Electro-Mechanics | C_0805 | C12, C15, C16, C18, C21 |
| 2 | 2.2kΩ UNI-ROYAL(Uniroyal Elec) | R_0805 | R1, R6 |
| 3 | 10kΩ UNI-ROYAL(Uniroyal Elec) | R_0805 | R2, R11, R13 |
| 2 | 5.1kΩ UNI-ROYAL(Uniroyal Elec) | R_0805 | R3, R4 |
| 2 | 1kΩ UNI-ROYAL(Uniroyal Elec) | R_0805 | R5, R12 |
| 4 | 0Ω UNI-ROYAL(Uniroyal Elec) | R_0805 | R7, R8, R9, R10 |
| 2 | 100Ω UNI-ROYAL(Uniroyal Elec) | R_0805 | R14, R15 |
Nabby linux design files
The KiCad project lives in the JoachimBose/nabby-linux repository on GitHub; these links point at the commit this page was built from.
Nabby linux: common questions
How big is the Nabby linux PCB?
The Nabby linux measures 80 × 80.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Nabby linux?
60 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Nabby linux design files?
From the JoachimBose/nabby-linux repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Nabby linux design in my own project?
Yes, under the terms of its GPL-2.0 license, which JoachimBose chose for the repository.