132 open source boards using the AMS1117
Real designs built with the AMS1117, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
M8SBC-486
maniekx86
150 × 150 mm123 parts4LNo license253ESP8266
TranspOtterNG
Jana-Marie
100 × 45 mm59 parts2LNo license51ESP8266
Basicengine
uli
85 × 56 mm44 parts2LNo license48FPGA
Analog board
EERNINUO
125 × 90 mm281 parts4LGPL-3.036ESP32
Tiny sensor
larry-wong
22 × 71 mm18 parts2LNo license34ESP32
VFO-ESP32-Si5351
paulh002
108.4 × 79.9 mm95 parts2LNo license29ESP32
Terraesp
fehlfarbe
127 × 54.3 mm82 partsMIT25ESP32
Stacklight hardware
Tyler-Ward
132 × 60 mm115 parts2LCC-BY-SA-4.019ESP8266
Deck65
and3rson
254 × 80 mm183 parts2LGPL-3.015Expansion
kuku-199
52 × 43.4 mm52 parts2LNo license14STM32
RSTM32F030C8T6 ProMiniPlus
r-pv
25.9 × 56.4 mm27 parts2LGPL-3.014MIDI4MiSTer
KabukiFlux
44 × 44.8 mm27 parts2LMIT13STM32
STM32F030K6
r-pv
22 × 41 mm23 parts2LGPL-3.011ESP32
Wristwearable
wlatif-cmyk
22.4 × 32.2 mm39 parts4LNo license8STM32
ReST32 Main
berryelectronics
100 × 100 mm168 parts2LNo license7AVR/Arduino
Cosmoneer-Proto
cosmospioneering
70 × 50 mm71 parts4LNo license5Ft2232h
Xarlan
63 × 40 mm39 parts2LMPL-2.05TS Ext EPM3032
ponchick
94 × 74.3 mm50 parts2LNo license3ESP32
OpenAV
JIBSIL
70.3 × 53.9 mm35 parts2LMIT2RP2040/RP2350
Jackco esp32-pico
huming2207
57.2 × 24.6 mm29 parts2LNo license2RP2040/RP2350
Ad low noise float 2023 git
petermaerki
100 × 100 mm237 parts2LNo license1ESP32
Clean room slave
trieuhuyduc
165 × 110 mm207 parts2LNo license1RP2040/RP2350
Plank
thomas-maurice
229.8 × 77.9 mm146 parts2LNo license1AVR/Arduino
MDA80486SBC Final
mattheeewahn
150 × 150 mm123 parts4LGPL-3.01ModuCard-Backplane-Sixth-Sense
ArthorH
153.9 × 128.7 mm113 parts4LNo license1ESP32
Nerf-ATG-Electronics
nico25112005
56 × 38 mm87 parts4LCC-BY-NC-4.01STM32
AML Micromouse 24 2
Oopsan204
65 × 85 mm72 parts2LNo license1RISC-V
Wire connect checker
74th
53.5 × 69.5 mm72 parts2LMIT1ESP32
Dongle eaLIVE
joaogabrielsantosD
45 × 55 mm69 parts2LNo license1ESP32
Smart air
meeTeam05
100 × 100 mm62 parts2LMIT1ESP32
PressLog
bansalsaksham
117 × 81.5 mm45 parts2LNo license1RP2040/RP2350
Memcard dumper
jareklupinski
40 × 50 mm38 parts4LNo license1RP2040/RP2350
Siberian-01
luispa12
26 × 56.9 mm34 parts2LNo license1ESP8266
Wifi lamp
damianmoore
46.4 × 20.3 mm8 parts2LGPL-3.01- schematic only · 8 partsESP32
Routeur solaire
aginies
8 parts2LNo license1 STM32
NanoGaN
eren-akbayin
60 × 100 mm192 parts6LNo license0
How designs wire the AMS1117
Read from the KiCad layouts of 95 open source designs, one per repository: what each pin of the AMS1117 connects to, and the resistors, capacitors and other passives placed on it.
- The VI pin has a decoupling capacitor on 71 of 95 designs, most often 10 µF (then 100 nF).
- The ADJ pin is tied to GND on 77 of 95 designs (a signal on 17).
- The VO pin has a decoupling capacitor on 48 of 95 designs, most often 10 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ADJpin 1 | Connected to: GND 81% · a signal 18% | — |
| VOpin 2 | Connected to: 3.3V 78% · a signal 22% |
|
| VIpin 3 | Connected to: 5V 75% · a signal 25% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include M8SBC-486 by maniekx86, TranspOtterNG by Jana-Marie, Basicengine by uli and Analog board by EERNINUO.
The AMS1117 in open source designs
The gallery holds 132 open source boards using the AMS1117 from 100 GitHub repositories; a typical one measures about 58.7 × 54.6 mm and carries around 40 components.
80% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is M8SBC-486 by maniekx86.
Parts used alongside the AMS1117
Microcontrollers on boards using the AMS1117
What boards using the AMS1117 are built for
AMS1117: common questions
Where can I find a AMS1117 reference design?
Each of the 132 boards on this page is a real design using the AMS1117. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the AMS1117 VI pin?
The VI pin has a decoupling capacitor on 71 of 95 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 95 open source designs using the AMS1117.
How is the AMS1117 ADJ pin connected?
The ADJ pin is tied to GND on 77 of 95 designs (a signal on 17). Counted from the KiCad layouts of 95 open source designs using the AMS1117.
What decoupling capacitors do designs use on the AMS1117 VO pin?
The VO pin has a decoupling capacitor on 48 of 95 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 95 open source designs using the AMS1117.
What parts are used alongside the AMS1117?
The ESP32-S3-WROOM-1, CH340C, ESP32-WROOM-32, RP2040 and RTC_DS3231M appear in the most repositories here.
Which microcontrollers do boards using the AMS1117 use?
Most are built on ESP32 (40), STM32 (23), AVR/Arduino (20) and RP2040/RP2350 (9).
How big is a typical board using the AMS1117?
The median is 58.7 × 54.6 mm, and 80% are two-layer designs.
What is the most popular open source board using the AMS1117?
By GitHub stars, M8SBC-486 by maniekx86, with 253 stars.
Can I simulate one of these boards using the AMS1117 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.