HardLabs

Stm32f4-24-pin rev h3

johanputzolu-cmd·Onerom·hardware/pcb/verified/ice-24-usb-h3/kicad/stm32f4-24-pin-rev-h3.kicad_pcb

Stm32f4-24-pin rev h3 PCB layout, top view — open source STM32 board by johanputzolu-cmd

About the Stm32f4-24-pin rev h3 PCB

Stm32f4-24-pin rev h3 is an open source STM32 PCB design by johanputzolu-cmd, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 18.9 × 31.6 mm, with 36 components from 22 distinct parts.

Its main chip is the RP2354B, from the STM32 family. Other key parts include the 2332/2364 SOCKET, AP2112K-3.3 and USBLC6-2P6. By type, the board carries 11 capacitors, 8 test points, 4 ICs, 4 resistors, 3 connectors and 3 diodes.

From the project

Very similar to rev H2 but with the following changes: - Make holes for BOOT0/3V3 jumpers larger to make them easier to jump. - Added inline resistor between VBUS and PA9, to avoid potential ESD damage to STM32F4. - Various components moved around to make space for the new resist

Very similar to rev H2 but with the following changes: - Make holes for BOOT0/3V3 jumpers larger to make them easier to jump. - Added inline resistor between VBUS and PA9, to avoid potential ESD damage to STM32F4. - Various components moved around to make space for the new resistor. - Now a single drill file, combining PTH and NPTH.

There is a single set of gerbers, one CPL/POS file and one BOM file for the STM32F411RET6 MCU.

Main components on the Stm32f4-24-pin rev h3

RP2354B2332/2364 SOCKETAP2112K-3.3USBLC6-2P6

Stm32f4-24-pin rev h3 bill of materials (BOM)

36 components, 22 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
RP2354B
STM32F411RET6
U1
1
2332/2364 SOCKET
U2
1
AP2112K-3.3
U3
1
USBLC6-2P6
U4
1
CRYSTAL_GND24
12MHz
Y1
1
Conn_02x05_Odd_Even
J2
1
Conn_01x02_Pin
J3
1
USB_B_Micro
J6
2
0R/4.7uF/DNP
RC4, RC5
6
TestPoint
TP1, TP2, TP3, TP4, TP5, TP7
2
TestPoint
TP6, TP8
1
C2286
LED_Small
D1
2
1N5819WS
MSK4005
D2, D3
3
4.7UF
4.7uF
C1, C2, C3
4
0.1UF
0.1uF
C4, C5, C6, C8
1
4.7UF
0.1uF
C7
1
0.1UF
4.7uF/DNP/DNP
C9
2
0.1UF
33pF
C10, C11
1
10K
4K7
R1
1
4K7
R2
Show 2 more
QtyPartRefs
1
10K
1K
R3
1
33R
10K
R4

Stm32f4-24-pin rev h3 design files

The KiCad project lives in the johanputzolu-cmd/Onerom repository on GitHub; these links point at the commit this page was built from.

Stm32f4-24-pin rev h3: common questions

What microcontroller does the Stm32f4-24-pin rev h3 use?

The Stm32f4-24-pin rev h3 is built around the RP2354B, from the STM32 family.

How big is the Stm32f4-24-pin rev h3 PCB?

The Stm32f4-24-pin rev h3 measures 18.9 × 31.6 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Stm32f4-24-pin rev h3?

36 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Stm32f4-24-pin rev h3 design files?

From the johanputzolu-cmd/Onerom repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Stm32f4-24-pin rev h3 design in my own project?

Yes, under the terms of its CC-BY-SA-4.0 license, which johanputzolu-cmd chose for the repository.

Can I test firmware for the Stm32f4-24-pin rev h3 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in Onerom

Similar boards