DIY-HOTAS
jtljac·DIY-HOTAS·PCB/Joystick Controller/Joystick Controller.kicad_pcb
About the DIY-HOTAS PCB
DIY-HOTAS is an open source STM32 PCB design by jtljac, published on GitHub. It is a 2-layer board, with 57 components from 29 distinct parts.
Its main chip is the STM32F103C8Tx, from the STM32 family. Other key parts include the TLV76133DCY. By type, the board carries 19 diodes, 13 capacitors, 12 connectors, 7 resistors, 2 ICs and 2 switches.
From the project
A HOTAS Joystick mixing multiple existing projects, with custom STM32 based PCBs
My take on a custom HOTAS. Currently only WIP Joystick so far.
This project aims to take components from other custom joysticks to build one suited to me. It should be noted that I have not used a commercial HOTAS setup before, I just don't want to pay for that, so this project may include some naive decisions.
Main components on the DIY-HOTAS
DIY-HOTAS bill of materials (BOM)
57 components, 29 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F103C8Tx | LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | TLV76133DCY | SOT-223-3_TabPin2 | U4 |
| 1 | 16MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | SWD | J1 | |
| 1 | I2C1 | J2 | |
| 1 | Joystick X | J3 | |
| 1 | Joystick Y | J4 | |
| 1 | Brake Lever | J5 | |
| 1 | Face Top | J6 | |
| 1 | Face Bottom | J7 | |
| 1 | Joystick Button | J8 | |
| 1 | Pinky Button | J9 | |
| 1 | Primary Trigger | J10 | |
| 1 | Index Hat | J11 | |
| 1 | Thumb Hat | J12 | |
| 1 | Secondary Trigger Forwards | SW1 | |
| 1 | Secondary Trigger Backwards | SW2 | |
| 1 | 1N5819 | D_SOD-123 | D1 |
| 18 | 1N4148W | D_SOD-123 | D2, D3, D4, D5, D6, D7, D8, D9 +10 |
| 1 | 120R @ 100MHz | FB1 |
Show 9 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10u | C1 | |
| 5 | 100n | C2, C3, C4, C5, C9 | |
| 2 | 10n | C6, C7 | |
| 1 | 1u | C8 | |
| 1 | 1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10 |
| 1 | 2u2 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11 |
| 2 | 10p | C12, C13 | |
| 1 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 6 | 10K | R9, R10, R11, R12, R13, R14 |
DIY-HOTAS design files
The KiCad project lives in the jtljac/DIY-HOTAS repository on GitHub; these links point at the commit this page was built from.
DIY-HOTAS: common questions
What microcontroller does the DIY-HOTAS use?
The DIY-HOTAS is built around the STM32F103C8Tx, from the STM32 family.
How big is the DIY-HOTAS PCB?
The DIY-HOTAS has 2 copper layers and is 1.6 mm thick.
How many components are on the DIY-HOTAS?
57 components, from 29 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the DIY-HOTAS design files?
From the jtljac/DIY-HOTAS repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the DIY-HOTAS design in my own project?
The repository has no license, so all rights stay with jtljac. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the DIY-HOTAS without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k