ZooomVGA

Kacman62·ZooomVGA·KiCad_Files/STM32 VGA.kicad_pcb

ZooomVGA PCB layout, top view — open source STM32 board by Kacman62

About the ZooomVGA PCB

ZooomVGA is an open source STM32 PCB design by Kacman62, published on GitHub under the MIT license. It is a 2-layer board measuring 32.8 × 59.9 mm, with 29 components from 14 distinct parts.

Its main chip is the STM32F103C8Tx, from the STM32 family. Other key parts include the AMS1117-3.3. By type, the board carries 14 resistors, 6 capacitors, 3 connectors, 3 diodes, 2 ICs and 1 crystal.

It belongs with the dev boards & breakouts designs in this gallery.

From the project

An STM32 dev board complete with VGA out

I've been spending a lot of time on software recently and I wanted to do another hardware project. After browsing the Hack CLub slack, I saw there was a zoom call for Blueprint, the hardware program and I decided to join in. The theme was a Trace Race, where you try to make a board in the shortest amount of time. Just an hour before I saw a VGA library for the exact same STM32 module in the challenge and I knew what my proejct was going to be. The schematic was pretty quick to put together, using a USB C port, an ASM power regulator, the STM32F103C8, a Crystal Oscillator and the VGA port.…

ZooomVGA, from the project README
From the project README

Main components on the ZooomVGA

ZooomVGA bill of materials (BOM)

29 components, 14 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32F103C8Tx
U1
1
AMS1117-3.3
U2
1
Crystal_GND24
Y1
1
USB_C_Receptacle_USB2.0_16P
J1
2
Conn_01x17_Pin
J3, J4
3
LED
D1, D2, D3
2
.1n
C1, C3
4
10u
C2, C4, C5, C6
2
5.1k
R1, R2
2
22
R3, R4
1
10k
R5
1
100k
R6
5
330
R7, R8, R9, R10, R11
3
1k
R12, R13, R14

ZooomVGA design files

The KiCad project lives in the Kacman62/ZooomVGA repository on GitHub; these links point at the commit this page was built from.

ZooomVGA: common questions

What microcontroller does the ZooomVGA use?

The ZooomVGA is built around the STM32F103C8Tx, from the STM32 family.

How big is the ZooomVGA PCB?

The ZooomVGA measures 32.8 × 59.9 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the ZooomVGA?

29 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the ZooomVGA design files?

From the Kacman62/ZooomVGA repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the ZooomVGA design in my own project?

Yes, under the terms of its MIT license, which Kacman62 chose for the repository.

Can I test firmware for the ZooomVGA without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards