Rev3
keionbis·ServoControllerRev2·motor controller Serial/Rev3.kicad_pcb
About the Rev3 PCB
Rev3 is an open source STM32 PCB design by keionbis, published on GitHub. It is a 2-layer board measuring 38 × 18 mm, with 29 components from 20 distinct parts.
Its main chip is the STM32L432KCUX, from the STM32 family. Other key parts include the MA702, MC33926PNB, LP38690SD-ADJ_NOPB and LTC2850IS8PBF. By type, the board carries 9 capacitors, 9 resistors, 5 ICs, 3 connectors, 1 module and 1 crystal.
Main components on the Rev3
Rev3 bill of materials (BOM)
29 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MA702 | MA702 | IC1 |
| 1 | MC33926PNB | QFN80P800X800X220-33N | IC2 |
| 1 | LP38690SD-ADJ_NOPB | SON95P300X300X80-7N | IC3 |
| 1 | LTC2850IS8PBF | SOIC127P600X175-8N | IC4 |
| 1 | STM32L432KCUX STM32L432KCUx | QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U1 |
| 1 | Motor_DC | hv5932mgMotor | M1 |
| 1 | 32MHZ 32mhz | Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1 |
| 2 | CONN_01X06_MALE Conn_01x04_Male | Molex_CLIK-Mate_502494-0470_1x04-1MP_P2.00mm_Horizontal | J1, J2 |
| 1 | CONN_01X04_MALE Conn_01x04_Male | 1x4Pads | J3 |
| 1 | LED | LED_0603_1608Metric | D1 |
| 2 | 10PF 10pF | C_0402_1005Metric | C1, C2 |
| 4 | 1UF | C_0402_1005Metric | C3, C5, C8, C9 |
| 1 | 0.1UF | C_0402_1005Metric | C4 |
| 1 | 33NF 33nf | C_0402_1005Metric | C6 |
| 1 | 47UF | C_1206_3216Metric | C7 |
| 1 | 100K 100k | R_0402_1005Metric | R1 |
| 1 | 330 | R_0402_1005Metric | R2 |
| 1 | 120 | R_0402_1005Metric | R3 |
| 1 | 220 | R_0402_1005Metric | R4 |
| 5 | 1k | R_0402_1005Metric | R5, R6, R7, R8, R9 |
Rev3 design files
The KiCad project lives in the keionbis/ServoControllerRev2 repository on GitHub; these links point at the commit this page was built from.
Rev3: common questions
What microcontroller does the Rev3 use?
The Rev3 is built around the STM32L432KCUX, from the STM32 family.
How big is the Rev3 PCB?
The Rev3 measures 38 × 18 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Rev3?
29 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Rev3 design files?
From the keionbis/ServoControllerRev2 repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Rev3 design in my own project?
The repository has no license, so all rights stay with keionbis. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Rev3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in ServoControllerRev2
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k