HardLabs

PetSafe

kerby2000·PetSafe-PCB·schematic/PetSafe_1001339.kicad_sch

This repository ships a schematic but no board layout.

About the PetSafe PCB

PetSafe is an open source PIC PCB design by kerby2000, published on GitHub. It is a board, with 150 components from 62 distinct parts.

Its main chip is the PIC16F18855, from the PIC family. Other key parts include the S-1200B45?, SN74LVC2G14DBV?, SGM8542XS, MX512H and S-812C33AMC? / 3.3V. By type, the board carries 51 capacitors, 44 resistors, 22 test points, 10 transistors, 8 ICs and 6 diodes.

From the project

PetSafe PPA19-16811 / 100-1339 R03 A

Working reconstruction of the PetSafe PPA19-16811 main board, 100-1339 R03 A. All 150 catalog entries are drawn on one A2 KiCad 10 sheet, with wires within functional blocks and named nets between them. Entries include test pads and unpopulated options.

Start with the offline overview, the current completion checklist, or the printable status. Open the native schematic in KiCad 10. The single-sheet PDF and SVG are native KiCad exports.

Main components on the PetSafe

S-1200B45?SN74LVC2G14DBV?SGM8542XSPIC16F18855MX512HS-812C33AMC? / 3.3VU6A / DNP

PetSafe bill of materials (BOM)

150 components, 62 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
S-1200B45?
U1
1
SN74LVC2G14DBV?
U2
1
SGM8542XS
U3
1
PIC16F18855
U4
1
MX512H
U5
1
S-812C33AMC? / 3.3V
U6
1
DNP
U7
1
U6A / DNP
U106
1
FMOS3401A?
Q1
1
BC847B?
Q2
5
MMBTA55?
Q3, Q4, Q5, Q6, Q11
1
BC857C?
Q7
1
SIL3724A?
Q8
1
DNP
Q9
1
20 MHz
Y1
1
ICSP
J1
1
PIR BOARD
J3
1
MOTOR
J5
1
DNP
J6
1
pushbutton
S1
Show 42 more
QtyPartRefs
14
test point
TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP9 +6
1
GND
TP101
1
GND_RF / GND pad
TP102
1
VDD
TP103
1
VREF
TP104
1
ANT1 / ANTENNA A
TP105
1
ANT2 / ANTENNA B
TP106
1
BATTERY (+)
TP107
1
BATTERY (-)
TP108
1
2-colour LED?
LED1
1
BAV99?
D1
1
4P / unidentified
D2
1
BAV99? (A7)
D3
2
SD05? / TVS 5V
D4, D5
1
MMSZ5228BS? / 3.9V
D6
2
bead / L ?
L1, L2
1
1u?
C1
1
4.7u?
C2
3
DNP
C3, C4, C42
1
470uF / 16V
C5
13
?
C6, C10, C11, C13, C14, C16, C20, C27 +5
7
100n?
C7, C17, C24, C28, C32, C34, C35
12
?
C8, C9, C18, C19, C21, C22, C23, C25 +4
5
? (rear)
C12, C15, C38, C45, C48
2
18p?
C30, C31
3
1u?
C33, C36, C37
1
DNP
C49
1
C1A / DNP
C101
1
C2A / DNP
C102
6
DNP
R1, R2, R35, R36, R46, R47
2
330k
R3, R4
3
22
R5, R20, R37
4
1.2k
R6, R18, R25, R42
6
1.8k
R7, R11, R13, R14, R15, R16
4
220
R8, R9, R30, R31
10
10k
R10, R19, R21, R22, R27, R32, R33, R38 +2
2
5.6k
R23, R48
2
120k
R24, R26
1
1M
R28
2
15k
R29, R44
1
330
R41
1
6.8k
R43

PetSafe design files

The KiCad project lives in the kerby2000/PetSafe-PCB repository on GitHub; these links point at the commit this page was built from.

PetSafe: common questions

What microcontroller does the PetSafe use?

The PetSafe is built around the PIC16F18855, from the PIC family.

How many components are on the PetSafe?

150 components, from 62 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the PetSafe design files?

From the kerby2000/PetSafe-PCB repository on GitHub, which has the schematic, a netlist and the BOM; the links under Design files point to each one.

Can I use the PetSafe design in my own project?

The repository has no license, so all rights stay with kerby2000. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the PetSafe without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

Similar boards