Band MODULE V1 00
About the Band MODULE V1 00
Band MODULE V1 00 is an open source PCB design by kholia, published on GitHub under the Custom license license. It is a 2-layer board measuring 45.4 × 14.8 mm, with 12 components from 6 distinct parts.
By type, the board carries 7 capacitors, 3 inductors and 2 connectors.
It belongs with the audio and rf & radio designs in this gallery.
From the project
Direct-RF-Synthesis CW Beacon PoC using Raspberry Pi Pico. No Si5351 is needed. HF and VHF fox! Have fun! ;) Comes with 5W amplifier + LPF!
This project generates a RF signal by toggling a GPIO pin (of a Raspberry Pi Pico / Pico W board) at a high speed (HF frequency).
Note: This repository has pre-built firmware files in it (.uf2 files) for testing, and debugging purposes.
The following steps demonstrate the process of re-building the firmware from the source code.
To customize the CW message, CW speed, and the message, please edit the blink.pio and message.h files.
Band MODULE V1 00 bill of materials (BOM)
12 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 0022232041 Antenna Molex | PinHeader_1x4_P2.54mm_Drill1.02mm | J1 |
| 1 | 0022232041 input Molex | PinHeader_1x4_P2.54mm_Drill1.02mm | J2 |
| 2 | — | L_Toroid_Vertical_L10.0mm_W5.0mm_P5.08mm | L1, L2 |
| 1 | FT37_43 | L_Toroid_Vertical_L10.0mm_W5.0mm_P5.08mm | L3 |
| 6 | — | C_Disc_D5.0mm_W2.5mm_P2.50mm | C1, C2, C3, C4, C5, C6 |
| 1 | 100nF | C_Disc_D5.0mm_W2.5mm_P2.50mm | C7 |
Band MODULE V1 00 design files
The KiCad project lives in the kholia/pico-cw-beacon-drs repository on GitHub; these links point at the commit this page was built from.
Band MODULE V1 00: common questions
How big is the Band MODULE V1 00?
The Band MODULE V1 00 measures 45.4 × 14.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Band MODULE V1 00?
12 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Band MODULE V1 00 design files?
From the kholia/pico-cw-beacon-drs repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Band MODULE V1 00 design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
More boards in pico-cw-beacon-drs
Similar boards
KLOR
GEIGEIGEIST
160.2 × 118.3 mm79 parts2LGPL-3.01.2k
ButtonsLEDs
shanteacontrols
390 × 37 mm82 parts2LApache-2.0956
USB
52 × 12.6 mm6 parts2LApache-2.0956
Pots
390 × 93 mm75 parts2LApache-2.0956
PicoGUS Hand386
polpo
29.2 × 75.2 mm43 parts4LGPL-2.0800
Snark barker
schlae
231.1 × 106.7 mm193 parts2LNo license687