Microduck Thermal 65C R8

ldcyes·OpenDuck·hardware/kicad/Thermal_65C_R8/Microduck_Thermal_65C_R8.kicad_pcb

Microduck Thermal 65C R8 PCB layout, top view — open source board by ldcyes

About the Microduck Thermal 65C R8 PCB

Microduck Thermal 65C R8 is an open source PCB design by ldcyes, published on GitHub. It is a 2-layer board measuring 16 × 12 mm, with 3 components from 3 distinct parts.

Other key parts include the TMP302ADRLR. By type, the board carries 1 IC, 1 connector and 1 capacitor.

From the project

本仓库整理 Microduck 的结构、电气、步态数值验证,以及 RK3576 驱动和训练适配源。当前是工程仿真预发布,尚未通过实物制造与正常步速行走验收。

本仓库整理 Microduck 的结构、电气、步态数值验证,以及 RK3576 驱动和训练适配源。当前是工程仿真预发布,尚未通过实物制造与正常步速行走验收。

R29 将嘴部软件行程收至 0–10° 并修正下头壳;指定腿罩/电机配对在四条新质量慢速轨迹中的最低保守名义间隙下界为 11.407 mm。31 根线的防磨件和四工况动力学已补充,但嘴部闭合扭矩仍超过现行 0.05 Nm 结构限制,连续线束及制造公差尚无实物证明,不能放行行走。

沿用R25:31根头部导线改为底部接入,保留前盖与原外形比例;收拢活动线束并取消原侧面专用线孔。底部走线特写。仍为工程候选,离散转头检查不代表连续运动或实物验收。

历史四步回放:R27:R26整机运动回放。 使用已保存的195.44秒实际积分轨迹,逐帧驱动完整R26装配并复核覆盖件的刚体干涉增量;R26质量下的动力学和实物行走仍待验收。

Microduck Thermal 65C R8, from the project README
From the project README

Main components on the Microduck Thermal 65C R8

Microduck Thermal 65C R8 bill of materials (BOM)

3 components, 3 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TMP302ADRLR
65C HARD THERMAL STOP
U1
1
SM03B-SRSS-TB(LF)(SN)
3V3 / FAULT OD
J1
1
GRM188R71H104KA93D
100nF
C1

Microduck Thermal 65C R8 design files

The KiCad project lives in the ldcyes/OpenDuck repository on GitHub; these links point at the commit this page was built from.

Microduck Thermal 65C R8: common questions

How big is the Microduck Thermal 65C R8 PCB?

The Microduck Thermal 65C R8 measures 16 × 12 mm, has 2 copper layers and is 1 mm thick.

How many components are on the Microduck Thermal 65C R8?

3 components, from 3 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Microduck Thermal 65C R8 design files?

From the ldcyes/OpenDuck repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Microduck Thermal 65C R8 design in my own project?

The repository has no license, so all rights stay with ldcyes. Use it as a reference, and ask the author before reusing the design.

More boards in OpenDuck