NanoProgrammer
About the NanoProgrammer PCB
NanoProgrammer is an open source PCB design by LithosphereRocketry, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 29.5 × 14.2 mm, with 23 components from 11 distinct parts.
Other key parts include the DS2480B+ and HT42B534. By type, the board carries 5 test points, 5 capacitors, 5 resistors, 3 connectors, 3 diodes and 2 ICs.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
A very small dual-deployment altimeter for low- and mid-power rockets.
Firmware for NanoDeploy is located in the firmware directory. Most day-to-day operations are handled by that folder's Makefile.
The setup process for TI's MSP430 toolchain is pretty miserable on modern Linux. See firmware/install-notes.md for details.
Run make run to upload the code to an attached MSP430 development board.
Run make gdb to upload the code to the attached dev board and start a GDB server session. From a separate terminal, then run msp430-gdb. (The included .gdbinit file should take care of all the necessary setup.)
Main components on the NanoProgrammer
NanoProgrammer bill of materials (BOM)
23 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DS2480B+ | SO-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | HT42B534 | SSOP-10_3.9x4.9mm_P1.00mm | U2 |
| 1 | USB_A | USB_A_AdamTech_USB-AP-S-RA_Horizontal | J1 |
| 1 | Conn_01x05 | PinHeader_1x05_P2.54mm_Vertical | J3 |
| 1 | Conn_01x04 | Molex_PicoBlade_53047-0410_1x04_P1.25mm_Vertical | J4 |
| 5 | TestPoint | TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | TP1, TP2, TP3, TP4, TP5 |
| 3 | RED | LED_0603_1608Metric | D1, D2, D3 |
| 3 | 0.1uF | C_0402_1005Metric | C1, C2, C5 |
| 2 | 47p | C_0402_1005Metric | C3, C4 |
| 2 | 33 | R_0402_1005Metric | R1, R2 |
| 3 | 330 | R_0402_1005Metric | R3, R4, R5 |
NanoProgrammer design files
The KiCad project lives in the LithosphereRocketry/NanoDeploy repository on GitHub; these links point at the commit this page was built from.
NanoProgrammer: common questions
How big is the NanoProgrammer PCB?
The NanoProgrammer measures 29.5 × 14.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the NanoProgrammer?
23 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the NanoProgrammer design files?
From the LithosphereRocketry/NanoDeploy repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the NanoProgrammer design in my own project?
Yes, under the terms of its GPL-3.0 license, which LithosphereRocketry chose for the repository.
More boards in NanoDeploy
Similar boards
88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2k
134pin 7-967288-1
139.7 × 73.7 mm38 parts2LGPL-3.01.2k
Breakout 60pin EEC-IV
139.7 × 62.2 mm15 parts2LGPL-3.01.2k
Breakout 112pin Connector
174 × 58 mm39 parts2LGPL-3.01.2k
Eecv breakout
140.8 × 53.7 mm9 parts4LGPL-3.01.2k
Rj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979