HardLabs

Soldering Fume Extractor

lizard-electronics·Soldering_Fume_Extractor·1_Hardware/PCB/FumeExtractorBoard_v1/FumeExtractorBoard_v1.kicad_pcb

Soldering Fume Extractor PCB layout, top view — open source AVR/Arduino board by lizard-electronics

About the Soldering Fume Extractor PCB

Soldering Fume Extractor is an open source AVR/Arduino PCB design by lizard-electronics, published on GitHub. It is a 2-layer board measuring 140 × 30 mm, with 59 components from 39 distinct parts.

Its main chip is the ATMEGA328P-A, from the AVR/Arduino family. Other key parts include the TP6841S6-A. By type, the board carries 17 resistors, 16 capacitors, 6 connectors, 4 switches, 3 transistors and 3 jumpers.

From the project

Portable soldering fume extractor based on an ATmega328P MCU.

Main components on the Soldering Fume Extractor

TP6841S6-AATMEGA328P-A

Soldering Fume Extractor bill of materials (BOM)

59 components, 39 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TP6841S6-A
U201
1
ATMEGA328P-A
ATmega328P-A
U301
1
AO3401A
Q201
1
SS8050
Q501
1
AO3400A
Q601
1
16MHZ
16MHz
Y301
1
C718037
Barrel_Jack_MountingPin
J201
1
PINHEADER_2.54MM
PinHeader_2.54mm
J301
1
PINHEADER_2.54MM
PinHeader_2.54mm
J302
1
AVR-ISP-6
J303
1
JST-PH-6-F
J501
1
JST-PH-4-F
J601
1
800MA
800mA
F201
1
Jumper 5V
JP201
1
Jumper Fan Driver
JP601
1
Jumper 4-Pin Fan
JP602
2
C2800116
SW_SPDT
SW201, SW402
1
SW_Push
SW301
1
SW_Push
SW401
1
C965815
Green
D201
Show 19 more
QtyPartRefs
1
C965813
Orange
D301
1
SS14
D601
1
C79382
120 @ 100MHz
FB201
1
10UH
10uH
L201
1
10UH
10uH
L301
8
0.1UF
0.1uF
C201, C302, C303, C304, C307, C308, C401, C402
1
0.1UF
0.1uF
C202
4
22UF
22uF
C203, C204, C205, C501
1
4.7UF
4.7uF
C301
2
12PF
12pF
C305, C306
1
100K
100k
R201
1
105K
105k
R202
1
20K
20k
R203
2
1k
R204, R302
6
10K
10k
R301, R403, R404, R501, R504, R601
2
470
R401, R402
1
47K
47k
R502
2
150
R503, R602
1
1k
R505

Soldering Fume Extractor design files

The KiCad project lives in the lizard-electronics/Soldering_Fume_Extractor repository on GitHub; these links point at the commit this page was built from.

Soldering Fume Extractor: common questions

What microcontroller does the Soldering Fume Extractor use?

The Soldering Fume Extractor is built around the ATMEGA328P-A, from the AVR/Arduino family.

How big is the Soldering Fume Extractor PCB?

The Soldering Fume Extractor measures 140 × 30 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Soldering Fume Extractor?

59 components, from 39 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Soldering Fume Extractor design files?

From the lizard-electronics/Soldering_Fume_Extractor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Soldering Fume Extractor design in my own project?

The repository has no license, so all rights stay with lizard-electronics. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Soldering Fume Extractor without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards