Eqs energy harvesting frontend

lkoehli·eqs-energy-harvesting-frontend·hardware/kicad/BSc_Thesis.kicad_pcb

Eqs energy harvesting frontend PCB layout, top view — open source STM32 board by lkoehli

About the Eqs energy harvesting frontend PCB

Eqs energy harvesting frontend is an open source STM32 PCB design by lkoehli, published on GitHub. It is a 4-layer board measuring 87.4 × 35.6 mm, with 108 components from 43 distinct parts.

Its main chip is the STM32U385CGU6Q, from the STM32 family. Other key parts include the TPS62840DLCR, MAX30009ENA+, MAX5395LATA+, ISM330IS and AEM30300. By type, the board carries 38 capacitors, 31 resistors, 16 connectors, 7 ICs, 7 diodes and 6 inductors.

It belongs with the test & measurement designs in this gallery.

From the project

Discrete EQS body-channel energy-harvesting frontend (1–21 MHz): KiCad hardware, measurement setups and bench automation.

Open kicad/BScThesis.kicadpro in KiCad 10. All footprints resolve from kicad/lib through the project library tables, so no global library setup is needed. Symbols are embedded in the schematic sheets.

The schematic is rev 1.1 (errata corrected) while the layout is rev 1.0 as fabricated. KiCad therefore reports two net differences between schematic and PCB: the HW-1 and HW-2 fixes. Don't run Update PCB from Schematic unless you are starting the rev 1.1 layout.

Eqs energy harvesting frontend, from the project README
From the project README

Main components on the Eqs energy harvesting frontend

STM32U385CGU6QTPS62840DLCRMAX30009ENA+MAX5395LATA+ISM330ISAEM30300SIP32431DR3

Eqs energy harvesting frontend bill of materials (BOM)

108 components, 43 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32U385CGU6Q
STMicroelectronics
U1
1
TPS62840DLCR
Texas Instruments
U2
1
MAX30009ENA+
Analog Devices (Maxim)
U3
1
MAX5395LATA+
Analog Devices (Maxim)
U4
1
ISM330IS
STMicroelectronics
U5
1
AEM30300
e-peas
U6
1
SIP32431DR3
SiP32431DR3
Vishay
U7
1
FTSH-107-01-L-DV-K
Samtec
J1
4
BCT1812M101AG
TDK
J2, J3, J4, J5
2
CONN_01X03_PIN
Conn_01x03_Pin
J6, J10
6
RFPC-SMA28-F
GradConn
J7, J9, J11, J13, J14, J15
1
CONN_01X12_PIN
Conn_01x12_Pin
J8
1
CONN_01X10_PIN
Conn_01x10_Pin
J12
1
CONN_01X02_PIN
Conn_01x02_Pin
J16
1
430182050816
SW_Push
Würth Elektronik
SW1
2
WBC16-1TL
Coilcraft
T1, T2
4
SMS7630-079LF
Skyworks Solutions
D1, D2, D3, D4
3
SML-P11UTT86
LED_SML-P11UTT86
ROHM
D5, D6, D7
1
BLM15PX471SZ1D
470R
Murata
FB1
2
CIGT201610EH2R2MNE
2.2uH
Samsung Electro-Mechanics
L1, L2
Show 23 more
QtyPartRefs
1
DFE252010F-100M=P2
Murata
L3
2
LQH32NH180J23L
Murata
L4, L5
14
100N
100n
C1, C5, C6, C7, C9, C10, C11, C12 +6
1
1u
C2
2
2.2U
2.2u
C3, C4
5
10U
10u
C8, C14, C17, C20, C22
2
10N
10n
C13, C39
1
100U
100u
C15
1
4.7U
4.7u
C16
1
22U
22u
C18
1
GRM155R61E105KA12J
1uF
Murata
C24
3
47N
47n
C25, C26, C27
2
3p
C30, C33
3
1n
C31, C34, C35
2
4.7N
4.7n
C32, C36
2
100R
R1, R14
1
10K
10k
R2
16
0R
R3, R4, R5, R6, R7, R8, R9, R10 +8
2
470R
R12, R13
4
4.7K
4.7k
R15, R16, R17, R18
3
10R
R19, R20, R21
2
100K
100k
R24, R30
1
680R
R31

Eqs energy harvesting frontend design files

The KiCad project lives in the lkoehli/eqs-energy-harvesting-frontend repository on GitHub; these links point at the commit this page was built from.

Eqs energy harvesting frontend: common questions

What microcontroller does the Eqs energy harvesting frontend use?

The Eqs energy harvesting frontend is built around the STM32U385CGU6Q, from the STM32 family.

How big is the Eqs energy harvesting frontend PCB?

The Eqs energy harvesting frontend measures 87.4 × 35.6 mm, has 4 copper layers and is 1.0032 mm thick.

How many components are on the Eqs energy harvesting frontend?

108 components, from 43 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Eqs energy harvesting frontend design files?

From the lkoehli/eqs-energy-harvesting-frontend repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Eqs energy harvesting frontend design in my own project?

The repository has no license, so all rights stay with lkoehli. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Eqs energy harvesting frontend without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards