GCVideo-DVI
loudiwang·GCVideo-DVI-PCB·KiCAD/fujiflex.kicad_pcb
About the GCVideo-DVI PCB
GCVideo-DVI is an open source FPGA PCB design by loudiwang, published on GitHub under the SHL-2.1 license. It is a 2-layer board measuring 27.7 × 30 mm, with 24 components from 13 distinct parts.
Its main chip is the XC3S200A-4VQG100C, from the FPGA family. Other key parts include the AT25SF041B-MAHD-T and TPS7A0512PDBZR. By type, the board carries 11 capacitors, 7 resistors, 3 ICs, 1 connector, 1 jumper and 1 diode.
From the project
OSHW GCVideo DVI flex for Nintendo Wii. Tested and working! Solderpad Hardware License v2.1
OSHW GCVideo DVI flex for Nintendo Wii. Tested and working! Solderpad Hardware License v2.1
Special thanks to loopj for testing the FPC and writing the assembly+install documentation!
The total BOM cost for fujiflex is around 10USD. If you're paying more than $5 per FPGA, you are being ripped off!
- A steel solderpaste stencil with etching or electropolishing is highly recommended for assembly. JLCPCB is a good source. - If you intend to program the SPI flash in-system, do not place R6.

Main components on the GCVideo-DVI
GCVideo-DVI bill of materials (BOM)
24 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XC3S200A-4VQG100C | QFP50P1600X1600X120-100N | U1 |
| 1 | AT25SF041B-MAHD-T | SON50P300X200X60-9N-D | U2 |
| 1 | TPS7A0512PDBZR | SOT-23 | U3 |
| 1 | 505278-1933 | 5052781933 | J1 |
| 1 | SolderJumper_2_Open | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | BAT54XV2T1G | D_SOD-523 | D1 |
| 2 | 1uF | C_0402_1005Metric | C1, C2 |
| 9 | 0.1uF | C_0402_1005Metric | C3, C4, C5, C6, C7, C8, C9, C10 +1 |
| 2 | 10k | R_0402_1005Metric | R1, R2 |
| 1 | 330 | R_0402_1005Metric | R3 |
| 2 | 4.7k | R_0402_1005Metric | R4, R7 |
| 1 | 100K | R_0402_1005Metric | R5 |
| 1 | 0 | R_0402_1005Metric | R6 |
GCVideo-DVI design files
The KiCad project lives in the loudiwang/GCVideo-DVI-PCB repository on GitHub; these links point at the commit this page was built from.
- LayoutKiCAD/fujiflex.kicad_pcb
- SchematicKiCAD/fujiflex.kicad_sch
GCVideo-DVI: common questions
What microcontroller does the GCVideo-DVI use?
The GCVideo-DVI is built around the XC3S200A-4VQG100C, from the FPGA family.
How big is the GCVideo-DVI PCB?
The GCVideo-DVI measures 27.7 × 30 mm, has 2 copper layers and is 0.11 mm thick.
How many components are on the GCVideo-DVI?
24 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the GCVideo-DVI design files?
From the loudiwang/GCVideo-DVI-PCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the GCVideo-DVI design in my own project?
It is published under SHL-2.1, which limits how it may be reused; read the license before building on it.
Can I test firmware for the GCVideo-DVI without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug FPGA firmware against it before you order a PCB.
Similar boards
FPGA
Base board
GlasgowEmbedded
80 × 49 mm222 parts4L0BSD2.2kFPGA
Thunderscope Rev5.3
EEVengers
122.5 × 103.5 mm817 parts6LMIT1.3kFPGA
Usb sniffer
ataradov
58.2 × 38.1 mm86 parts2LBSD-3-Clause1.3kFPGA
Tomu, I'm
theacodes
13 × 9.4 mm40 parts4LMIT1.1kFPGA
Icepi zero
cheyao
65 × 30 mm143 parts4LSHL-2.1865FPGA
Gcvideo
ikorb
49 × 30 mm44 parts4LNo license765