Tiny waveform generator
m-chwast·tiny-waveform-generator·Hardware/wave-gen/wave-gen.kicad_pcb
About the Tiny waveform generator PCB
Tiny waveform generator is an open source STM32 PCB design by m-chwast, published on GitHub. It is a 4-layer board measuring 85 × 70 mm, with 137 components from 50 distinct parts.
Its main chip is the STM32H562VGTX, from the STM32 family. Other key parts include the DAC904E, USBLC6-2P6, LD1117_33, M24C64 and TSV792. By type, the board carries 55 resistors, 44 capacitors, 11 diodes, 9 ICs, 8 connectors and 5 switches.
From the project
Engineering thesis, Applied CS 2026
- STM32H562, LQFP100, 1MB flash, 600k RAM
- display SPI - display touch (not implemented) - SDc (not implemented)
- encoder - 3 buttons (vertical, horizontal, on-off)
Design: - VDDUSB connection - AN5711 2.1.3 - VBAT connection - AN5711 2.1.4 - power connection - AN5711 fig. 6 - VREF+ connection - AN5711 fig. 6 with note
- BOOT0 resistor - to allow entering bootloader by manually shorting BOOT0 pin to VDD
Main components on the Tiny waveform generator
Tiny waveform generator bill of materials (BOM)
137 components, 50 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32H562VGTX STM32H562VGTx | LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | DAC904E | PW28 | U2 |
| 1 | USBLC6-2P6 | SOT-666 | U3 |
| 2 | LD1117_33 | SOT-223-3_TabPin2 | U4, U5 |
| 1 | M24C64 | SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | TSV792 | SOIC-8_3.9x4.9mm_P1.27mm | U7 |
| 1 | LM4040DBZ-2.5 | SOT-23 | U8 |
| 1 | TL1431A | SOT-23 | U9 |
| 1 | BC847 | SOT-23 | Q1 |
| 1 | 8M | Crystal_SMD_HC49-SD_HandSoldering | Y1 |
| 1 | SWD | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | USB_C_RECEPTACLE_USB2.0_16P USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J2 |
| 1 | DISP_TOUCH | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | DISP | PinHeader_1x14_P2.54mm_Vertical | J4 |
| 1 | OUT | BNC_Amphenol_B6252HB-NPP3G-50_Horizontal | J5 |
| 1 | UART | PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | PWR_IN | PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | OUT | PinHeader_1x02_P2.54mm_Vertical | J8 |
| 2 | 500MA 500mA | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1, F2 |
| 1 | Y14X-1C-XXDS Y14x-1C-xxDS | Relay_SPDT_HsinDa_Y14 | K1 |
Show 30 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | tactile | SW_DIP_SPSTx01_Slide_6.7x4.1mm_W6.73mm_P2.54mm_LowProfile_JPin | SW1 |
| 3 | tactile | tact-switch-6x6 | SW2, SW3, SW4 |
| 1 | Encoder | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW5 |
| 3 | LED | LED_D5.0mm | D1, D2, D3 |
| 6 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4, D5, D6, D7, D8, D9 |
| 2 | D_Schottky | D_SOD-323_HandSoldering | D10, D11 |
| 23 | 100N 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4, C5, C6, C7, C11 +15 |
| 2 | 2U2 2u2 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C9 |
| 3 | 4U7 4u7 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C25, C27 |
| 1 | 1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C12 |
| 2 | 20P 20p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C14, C15 |
| 5 | 10U 10u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C17, C18, C29, C43, C44 |
| 2 | 10N 10n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C35, C36 |
| 2 | 100p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C37, C38 |
| 1 | 10n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C39 |
| 3 | 100U 100u | CP_Radial_D5.0mm_P2.00mm | C40, C41, C42 |
| 1 | 47R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 10 | 4K7 4k7 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R10, R11, R12, R28, R29, R30, R36 +2 |
| 12 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R31, R32, R33, R34, R35, R39, R43 +4 |
| 5 | 220R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R5, R45, R46, R50 |
| 2 | 5K1 5k1 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R7 |
| 2 | 10K 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R9 |
| 1 | 4k7 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13 |
| 4 | 50R 0.1% | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14, R15, R16, R17 |
| 3 | 2k 0.1% | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18, R52, R53 |
| 7 | 0R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19, R20, R21, R22, R41, R54, R55 |
| 3 | 2k3 0.1% | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R23, R26, R27 |
| 2 | 1k 0.1% | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R24, R25 |
| 2 | 2K2 2k2 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R37, R38 |
| 1 | 470R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R40 |
Tiny waveform generator design files
The KiCad project lives in the m-chwast/tiny-waveform-generator repository on GitHub; these links point at the commit this page was built from.
Tiny waveform generator: common questions
What microcontroller does the Tiny waveform generator use?
The Tiny waveform generator is built around the STM32H562VGTX, from the STM32 family.
How big is the Tiny waveform generator PCB?
The Tiny waveform generator measures 85 × 70 mm, has 4 copper layers and is 1.605 mm thick.
How many components are on the Tiny waveform generator?
137 components, from 50 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Tiny waveform generator design files?
From the m-chwast/tiny-waveform-generator repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Tiny waveform generator design in my own project?
The repository has no license, so all rights stay with m-chwast. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Tiny waveform generator without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k