N0183to2k
mbouyer·n0183to2k·hardware/n0183to2k.kicad_pcb
About the N0183to2k PCB
N0183to2k is an open source PIC PCB design by mbouyer, published on GitHub under the BSD-2-Clause license. It is a 2-layer board measuring 60 × 60 mm, with 37 components from 24 distinct parts.
Its main chip is the PIC18F27Q84_ISS, from the PIC family. Other key parts include the TLE9250VSJXUMA1, mic5504-3.3 and LDL1117S50. By type, the board carries 10 resistors, 9 capacitors, 6 connectors, 4 ICs, 4 diodes and 3 transistors.
It belongs with the sensors designs in this gallery.
From the project
generic NMEA0183 to N2K gateway
This is a generic NMEA0183 to N2K gateway, derived from my weatherstation sensor board. It has a NMEA0183 input, switchable 12v power supply output and a 3.3v i2c connector for additional sensors (e.g. BME280 or SHT20)
Main components on the N0183to2k
N0183to2k bill of materials (BOM)
37 components, 24 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | PIC18F27Q84_ISS | SOIC-28W_7.5x17.9mm_P1.27mm | U1 |
| 1 | TLE9250VSJXUMA1 | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | mic5504-3.3 | SOT-23-5_HandSoldering | U3 |
| 1 | LDL1117S50 | SOT-223-3_TabPin2 | U4 |
| 2 | BSS123 | SOT-23 | Q1, Q3 |
| 1 | DMG2307L | SOT-23 | Q2 |
| 1 | 10Mhz | Crystal_HC18-U_Vertical | Y1 |
| 1 | NMEA0183 (wind) | TerminalBlock_bornier-3_P5.08mm | J1 |
| 1 | Conn_01x06_Male | PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | Conn_01x05_Male | PinHeader_1x05_P2.54mm_Vertical | J3 |
| 2 | RJ45 | RJ45_Amphenol_54602-x08_Horizontal | J4, J5 |
| 1 | Conn_02x03_Odd_Even | PinHeader_2x03_P2.54mm_Vertical | J6 |
| 3 | SMBJ16A | D_SMB_Handsoldering | D1, D2, D4 |
| 1 | red | LED_D3.0mm | D3 |
| 2 | 22pF | C_Disc_D3.8mm_W2.6mm_P2.50mm | C1, C2 |
| 4 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4, C5, C7 |
| 2 | 1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6, C8 |
| 1 | 10uF | C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C9 |
| 5 | 10K | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4, R8 |
| 1 | 1K | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 4K7 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | 4K7 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R7 |
| 1 | 100 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9 |
| 1 | 330 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R10 |
N0183to2k design files
The KiCad project lives in the mbouyer/n0183to2k repository on GitHub; these links point at the commit this page was built from.
N0183to2k: common questions
What microcontroller does the N0183to2k use?
The N0183to2k is built around the PIC18F27Q84_ISS, from the PIC family.
How big is the N0183to2k PCB?
The N0183to2k measures 60 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the N0183to2k?
37 components, from 24 distinct parts. The full bill of materials is listed on this page.
Where can I download the N0183to2k design files?
From the mbouyer/n0183to2k repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the N0183to2k design in my own project?
Yes, under the terms of its BSD-2-Clause license, which mbouyer chose for the repository.
Can I test firmware for the N0183to2k without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
Similar boards
PIC
Pslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7kPIC
Lens
ervanalb
80 × 80 mm53 parts4LNo license515PIC
Micro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414PIC
GB-CART256K-A
Gekkio
51.4 × 61 mm17 parts2LCC-BY-4.0379PIC
GB-CARTPP-DIY
Gekkio
100 × 100 mm22 parts2LCC-BY-4.0379PIC
GB-LIVE32
Gekkio
51.4 × 61 mm46 parts4LCC-BY-4.0379