SolenoidDriver
mechaken·SolenoidDriver
About the SolenoidDriver PCB
SolenoidDriver is an open source STM32 PCB design by mechaken, published on GitHub under the MIT license. It is a 2-layer board measuring 84.3 × 50 mm, with 59 components from 18 distinct parts.
Its main chip is the STM32F303K8Tx, from the STM32 family. Other key parts include the Si8621AB-B-ISR, NJM7812, AP2210N-3.3TRG1, MCP2562-E-SN and ULN2003. By type, the board carries 19 connectors, 18 diodes, 11 capacitors, 9 ICs, 1 switch and 1 resistor.
From the project
Solenoid drive circuit using PCIe with unique pin definition
最大17個のソレノイドを接続と駆動ができます。(17個も駆動させない場合は、A-Cのうち使用する行に接続されているダーリントントランジスタやその他部品のみ実装し、動作させることも可能です。)
作成しているモータードライバ(CAN-H-BridgeSoloMD)とほぼ同じ大きさなので、同一のマザーボードの中にモータードライバと本基板を入れることが可能です。

Main components on the SolenoidDriver
SolenoidDriver bill of materials (BOM)
59 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Si8621AB-B-ISR | SOIC127P600X175-8N | IC1 |
| 1 | NJM7812 | TO-252-2 | U1 |
| 2 | AP2210N-3.3TRG1 | SOT-23_Handsoldering | U2, U4 |
| 1 | STM32F303K8Tx | LQFP-32_7x7mm_P0.8mm | U3 |
| 1 | MCP2562-E-SN | SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 3 | ULN2003 | SOIC-16_3.9x9.9mm_P1.27mm | U6, U7, U8 |
| 17 | Conn_01x02 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1, J2, J3, J4, J6, J7, J8, J9 +9 |
| 1 | Conn_01x03 | PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | Conn_01x05 | PinHeader_1x05_P2.54mm_Vertical | J10 |
| 1 | IKD0403101 | DIP-8_W7.62mm | S1 |
| 17 | D | D_2010_5025Metric_Pad1.52x2.65mm_HandSolder | D1, D2, D3, D4, D5, D6, D7, D8 +9 |
| 1 | D_Schottky | D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D11 |
| 4 | 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3, C6, C9 |
| 1 | 0.33u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 2 | 1.0u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C7 |
| 2 | 2.2u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C8 |
| 2 | 10u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C11 |
| 1 | 10K | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
SolenoidDriver design files
The KiCad project lives in the mechaken/SolenoidDriver repository on GitHub; these links point at the commit this page was built from.
- LayoutSolenoid_Valve.kicad_pcb
SolenoidDriver: common questions
What microcontroller does the SolenoidDriver use?
The SolenoidDriver is built around the STM32F303K8Tx, from the STM32 family.
How big is the SolenoidDriver PCB?
The SolenoidDriver measures 84.3 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SolenoidDriver?
59 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the SolenoidDriver design files?
From the mechaken/SolenoidDriver repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the SolenoidDriver design in my own project?
Yes, under the terms of its MIT license, which mechaken chose for the repository.
Can I test firmware for the SolenoidDriver without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k