57 open source boards using the MCP2562-E-SN
Real designs built with the MCP2562-E-SN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
DropBear
speeduino
116.1 × 98 mm196 parts2LNo license282PIC
CANPower
RaphWeyman
75 × 35 mm62 parts2LGPL-2.010Controllino can
HarveyBates
19.2 × 34 mm12 parts2LGPL-3.05ESP32
ESP32indEVB
gmarocco
99.2 × 94.2 mm194 parts4LNo license4NXP
Teensy fendt-CAN
tomstix
112 × 64 mm46 parts2LNo license4STM32
Power board
tudsat-rocket
78 × 95 mm142 parts4LNo license3AVR/Arduino
Kicad nmea2000 sensor
olliiiver
100 × 38 mm32 parts2LMIT3ESP32
URC
spikonado
110 × 90 mm150 parts4LCERN-OHL-W-2.02STM32
GN10Mainboard
ararobo
80 × 60 mm124 parts4LNo license2Microchip SAM
Beetle v1.001 bothfill
Autohome2
48 × 26 mm37 parts2LGPL-2.02Raspberry Pi
Handcart hw
eagletrt
262.2 × 100 mm196 parts2LNo license1STM32
Carte puissance crac v2
Achille-92
62 × 88 mm60 parts2LNo license1STM32
PowerCutoffBoard1
ararobo
50 × 45 mm42 parts2LNo license1RP2040/RP2350
OAM-KNX2HovalGateway
Blizzard26
80 × 60 mm41 parts2LNo license1PIC
BMS 02
Voltworks-Garage
96.7 × 175.6 mm614 parts4LGPL-3.00Gen 1 Hayabusa ECU
HasiKe
148 × 111.5 mm293 parts2LNo license0STM32
BUT Pneumobil - ECU board
kajusK
143.8 × 80 mm261 parts2LNo license0ESP32
Bridge writer
tmcit-ararobo-2026a
100 × 65 mm226 parts4LMIT0RP2040/RP2350
Base18
M-o-a-T
140.4 × 84.9 mm162 parts2LNo license0CabShield
Avery-Jutkowitz
200 × 150 mm141 parts4LNo license0DashShield
GryphonRacingFSAE
58.3 × 62.5 mm112 parts2LNo license0STM32
Daly to lithium balance adapter
cepr
160 × 100 mm111 parts2LNo license0STM32
RJX-Embedded-Training-Kit
MUDAL
69.7 × 70.9 mm103 parts2LGPL-3.00RP2040/RP2350
PowerControlModule
tokai-student-rocket-project
90 × 70 mm80 parts2LNo license0Luckhead
baden
55.6 × 68.4 mm75 parts2LNo license0STM32
UGR-22 Screen
z8bi
69.2 × 50 mm70 parts2LNo license0STM32
SolenoidDriver
mechaken
84.3 × 50 mm59 parts2LMIT0STM32
G473 generic gen1 board
hit4752
50 × 50 mm49 parts4LNo license0NXP
K20dx256vlh7-dev board
njl7502l
35.8 × 28.2 mm39 parts2LNo license0ESP32
SPM-ESPSM-V1
caketetu
26.4 × 36.9 mm29 parts2LNo license0- schematic only · 6 partsPIC
Esp32-s3-flight controller
adithya-in
6 partsNo license0 Raspberry Pi
CanHat
bondus
65 × 30 mm33 parts2LGPL-3.0373Microchip SAM
Beetle
Autohome2
44.5 × 19.5 mm29 parts2LGPL-2.02PIC
BMS 01
Voltworks-Garage
96.7 × 175.7 mm598 parts4LGPL-3.00STM32
BUT Pneumobil - HMI
kajusK
133.5 × 95 mm115 parts2LNo license0AVR/Arduino
FlightModule
tokai-student-rocket-project
90 × 70 mm70 parts2LNo license0
How designs wire the MCP2562-E-SN
Read from the KiCad layouts of 38 open source designs, one per repository: what each pin of the MCP2562-E-SN connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a decoupling capacitor on 25 of 38 designs, most often 100 nF (then 4.7 µF).
- The VIO pin has a decoupling capacitor on 25 of 38 designs, most often 100 nF (then 10 nF).
- The CANL pin has a series resistor on 25 of 38 designs, most often 120 Ω (then 60 Ω).
- The CANH pin has a series resistor on 20 of 38 designs, most often 120 Ω (then 60 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 2 | Connected to: GND 95% | — |
| VDDpin 3 | Connected to: 5V 95% |
|
| VIOpin 5 | Connected to: 3.3V 92% |
|
| CANLpin 6 | Connected to: A connector 82% |
|
| CANHpin 7 | Connected to: A connector 82% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CanHat by bondus, DropBear by speeduino, CANPower by RaphWeyman and Megaduino by brunob45.
The MCP2562-E-SN in open source designs
The gallery holds 57 open source boards using the MCP2562-E-SN from 39 GitHub repositories; a typical one measures about 80 × 61.2 mm and carries around 60 components.
73% are two-layer designs, the rest use four layers or more, and 26% carry an open source license.
The most starred is CanHat by bondus.
Parts used alongside the MCP2562-E-SN
Microcontrollers on boards using the MCP2562-E-SN
What boards using the MCP2562-E-SN are built for
MCP2562-E-SN: common questions
Where can I find a MCP2562-E-SN reference design?
Each of the 57 boards on this page is a real design using the MCP2562-E-SN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the MCP2562-E-SN VDD pin?
The VDD pin has a decoupling capacitor on 25 of 38 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 38 open source designs using the MCP2562-E-SN.
What decoupling capacitors do designs use on the MCP2562-E-SN VIO pin?
The VIO pin has a decoupling capacitor on 25 of 38 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 38 open source designs using the MCP2562-E-SN.
What resistor goes on the MCP2562-E-SN CANL pin?
The CANL pin has a series resistor on 25 of 38 designs, most often 120 Ω (then 60 Ω). Counted from the KiCad layouts of 38 open source designs using the MCP2562-E-SN.
What parts are used alongside the MCP2562-E-SN?
The MCP2515-xSO, USBLC6-2SC6, 3.3V, MCP2515-XST and AZ1117-3.3 appear in the most repositories here.
Which microcontrollers do boards using the MCP2562-E-SN use?
Most are built on STM32 (21), ESP32 (7), PIC (6) and RP2040/RP2350 (5).
How big is a typical board using the MCP2562-E-SN?
The median is 80 × 61.2 mm, and 73% are two-layer designs.
What is the most popular open source board using the MCP2562-E-SN?
By GitHub stars, CanHat by bondus, with 373 stars.
Can I simulate one of these boards using the MCP2562-E-SN before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.