Tas elrs
mhalaba·tas-elrs·hardware/TAS-RX-900-C3/TAS-RX-900-C3.kicad_pcb
About the Tas elrs PCB
Tas elrs is an open source PCB design by mhalaba, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 17 × 25 mm, with 5 components from 5 distinct parts.
By type, the board carries 2 connectors, 1 switch, 1 diode and 1 resistor.
It belongs with the robotics & motion and rf & radio designs in this gallery.
From the project
TAS-ELRS is an open-source, jamming-resistant radio link for drone control: encrypted RC commands (ChaCha20), anti-replay, EW-status telemetry to the flight controller, deterministic FHSS channel rotation, and months-long standby with authenticated wake-up. Hardened fork of ExpressLRS 4.1.0 — GPL-3.0 (original TAS files also MIT).
Referencyjna elektronika dla targetów firmware z tego forka.
RX 868/915 MHz: ESP32-C3 + E28-900M22S (SX1276). Zgodny z targetem UnifiedESP32C3900RXviaUART — zero zmian w firmware**.
- TAS-RX-900-C3/TAS-RX-900-C3.kicadsch — schemat (KiCad 8) - TAS-RX-900-C3/TAS-RX-900-C3.kicadpcb — szkielet PCB 25×35 mm (outline, footprints, GND zone; routing przed produkcją!) - TAS-RX-900-C3/PINOUT.md — pinout + zasady layoutu RF - TAS-RX-900-C3/BOM.csv — materiałówka (~12 pozycji) - ../src/hardware/RX/TAS RX 900 C3.json — hardware-def do flashowania unified targetu przez Configurator
Tas elrs bill of materials (BOM)
5 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ANT_SMA | SMA_EDGE_MOUNT | J1 |
| 1 | CRSF_JST-GH | JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_Horizontal | P1 |
| 1 | BIND_BTN | SW_SPST_PTS645 | SW1 |
| 1 | LED_G | LED_0603_1608Metric | D1 |
| 1 | 1k | R_0603_1608Metric | R1 |
Tas elrs design files
The KiCad project lives in the mhalaba/tas-elrs repository on GitHub; these links point at the commit this page was built from.
Tas elrs: common questions
How big is the Tas elrs PCB?
The Tas elrs measures 17 × 25 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Tas elrs?
5 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Tas elrs design files?
From the mhalaba/tas-elrs repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Tas elrs design in my own project?
Yes, under the terms of its GPL-3.0 license, which mhalaba chose for the repository.
Similar boards
Stack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kCube batteryboard
willem-pennings
95 × 95 mm4 parts2LGPL-3.01.1kTrollerv2
rene-dev
100 × 75 mm33 parts4LGPL-3.0979Powerstep
rene-dev
95.2 × 71.5 mm28 parts4LGPL-3.097911ua
rene-dev
57.3 × 19 mm26 parts2LGPL-3.0979Diff driver
rene-dev
32 × 22 mm14 parts2LGPL-3.0979