HardLabs

RollerShutterControlPanel

Mickyleitor·RollerShutterControlPanel·PCB_Design/RollerShutterControlPanel.kicad_pcb

RollerShutterControlPanel PCB layout, top view — open source AVR/Arduino board by Mickyleitor

About the RollerShutterControlPanel PCB

RollerShutterControlPanel is an open source AVR/Arduino PCB design by Mickyleitor, published on GitHub under the CERN-OHL-1.2 license. It is a 2-layer board measuring 110.6 × 50 mm, with 55 components from 33 distinct parts.

Its main chip is the Shield Arduino Pro Mini 3v3, from the AVR/Arduino family. Other key parts include the PS2705-1, 3v3 DCDC Converter Power Module and ESP-13-WROOM-02. By type, the board carries 16 resistors, 12 capacitors, 10 connectors, 6 switches, 4 ICs and 4 diodes.

It belongs with the rf & radio, displays & leds and iot & wireless designs in this gallery.

From the project

This project stores the ATmega328P and ESP8266 firmware code along the PCB Design files for a roller shutter control panel.

Embedded wall panel for motorized shutters over radio; with LCD; buttons; Wi-Fi via ESP8266; clock; and temperature. Open hardware with 3D-printed parts; off-the-shelf modules; and a PCB using an ATMega328P plus ESP8266.

Built to stop sunrise from waking me early; first a simple wall controller; then my 2020 Bachelor’s thesis; now an open build others can replicate; learn from; and adapt. Also a testbed for new ideas.

RollerShutterControlPanel, from the project README
From the project README

Main components on the RollerShutterControlPanel

PS2705-13v3 DCDC Converter Power ModuleESP-13-WROOM-02Shield Arduino Pro Mini 3v3

RollerShutterControlPanel bill of materials (BOM)

55 components, 33 distinct parts.

QtyPartRefs
1
PS2705-1
U1
1
3v3 DCDC Converter Power Module
U2
1
ESP-13-WROOM-02
U3
1
Shield Arduino Pro Mini 3v3
U4
1
S8550
Q1
1
PWR 5V
J1
1
PWR 5V AUX
J2
1
TRIGGER SEL
J3
1
PWR SEL
J4
1
Screw_Terminal_01x03
J5
1
RF TX
J6
1
RF RX
J7
1
MASTER UART COM
J8
1
LAMP
J9
1
LCD COM
J10
1
SRD-05VDC-SL-C
K1
1
Speaker
LS1
4
SW_Push
SW1, SW2, SW3, SW4
1
BOOT
SW5
1
RESET
SW6
Show 13 more
QtyPartRefs
1
1N5822
D1
1
LED
D2
1
1N4007
D3
1
LED1
D4
1
10uF
C1
5
0.1uF
C2, C3, C5, C10, C11
1
47uF
C4
5
1uF
C6, C7, C8, C9, C12
1
2.2k
R1
2
1k
R2, R3
5
10k
R4, R5, R6, R14, R15
6
15k
R7, R10, R11, R12, R13, R16
2
8.2k
R8, R9

RollerShutterControlPanel design files

The KiCad project lives in the Mickyleitor/RollerShutterControlPanel repository on GitHub; these links point at the commit this page was built from.

RollerShutterControlPanel: common questions

What microcontroller does the RollerShutterControlPanel use?

The RollerShutterControlPanel is built around the Shield Arduino Pro Mini 3v3, from the AVR/Arduino family.

How big is the RollerShutterControlPanel PCB?

The RollerShutterControlPanel measures 110.6 × 50 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the RollerShutterControlPanel?

55 components, from 33 distinct parts. The full bill of materials is listed on this page.

Where can I download the RollerShutterControlPanel design files?

From the Mickyleitor/RollerShutterControlPanel repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the RollerShutterControlPanel design in my own project?

Yes, under the terms of its CERN-OHL-1.2 license, which Mickyleitor chose for the repository.

Can I test firmware for the RollerShutterControlPanel without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards