HardLabs

Kill control

minamonra·MKiCadPro·Power/kill_control/kill_control.kicad_pcb

Kill control PCB layout, top view — open source STM32 board by minamonra

About the Kill control PCB

Kill control is an open source STM32 PCB design by minamonra, published on GitHub. It is a 2-layer board measuring 110 × 45 mm, with 68 components from 34 distinct parts.

Its main chip is the STM32F030K6Tx, from the STM32 family. Other key parts include the AMS1117-3.3 and TPS5430DDA. By type, the board carries 28 resistors, 26 capacitors, 4 connectors, 3 ICs, 2 LEDs and 2 inductors.

From the project

MKiCadPro

Main components on the Kill control

STM32F030K6TxAMS1117-3.3TPS5430DDA

Kill control bill of materials (BOM)

68 components, 34 distinct parts.

QtyPartRefs
1
STM32F030K6Tx
MCU1
1
AMS1117-3.3
U2
1
TPS5430DDA
U3
1
12MHz*
Y1
1
Debug
J1
1
~
J2
1
~
J3
1
t
J4
1
Boot
JP1
1
~
VD3
2
~
VD1, VD2
1
100мкГн
L1
1
22мкГн
L2
3
0,01
C1, C3, C22
1
0,01
C2
2
4,7
C6, C8
2
100*
C9, C10
3
100
C11, C14, C15
2
15
C12, C13
9
0,1
C16, C17, C18, C19, C24, C26, C28, C29 +1
Show 14 more
QtyPartRefs
2
22,0
C20, C23
1
220,0
C25
1
47,0
C27
1
2k7
R1
4
1k
R2, R4, R5, R12
2
15k
R3, R13
3
10k
R6, R27, R29
7
22
R7, R9, R10, R11, R14, R15, R16
1
*
R8
2
10
R17, R31
2
2k
R19, R20
4
150
R21, R22, R25, R26
1
3k
R23
1
3,24k
R30

Kill control design files

The KiCad project lives in the minamonra/MKiCadPro repository on GitHub; these links point at the commit this page was built from.

Kill control: common questions

What microcontroller does the Kill control use?

The Kill control is built around the STM32F030K6Tx, from the STM32 family.

How big is the Kill control PCB?

The Kill control measures 110 × 45 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Kill control?

68 components, from 34 distinct parts. The full bill of materials is listed on this page.

Where can I download the Kill control design files?

From the minamonra/MKiCadPro repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Kill control design in my own project?

The repository has no license, so all rights stay with minamonra. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Kill control without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in MKiCadPro

Similar boards