SkyOrcaRX
mohamedaminemb·SkyOrca-Hardware·hardware/SkyOrcaRX/kicad/SkyOrcaRX.kicad_pcb
About the SkyOrcaRX PCB
SkyOrcaRX is an open source STM32 PCB design by mohamedaminemb, published on GitHub under the CERN-OHL-S-2.0 license. It is a 4-layer board measuring 32 × 25 mm, with 16 components from 10 distinct parts.
Its main chip is the STM32F405RGTX, from the STM32 family. By type, the board carries 7 capacitors, 1 IC, 1 crystal, 1 switch and 1 resistor.
It belongs with the robotics & motion designs in this gallery.
From the project
Custom quadcopter drone hardware — SkyOrcaFC, SkyOrcaTX, SkyOrcaRX
Main components on the SkyOrcaRX
SkyOrcaRX bill of materials (BOM)
16 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F405RGTX ATmega2560-16A | TQFP-100_14x14mm_P0.5mm | U1 |
| 1 | 8 MHZ | Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 3 | Conn_01x02_Pin | PinHeader_1x02_P1.00mm_Vertical | I2C, UART1, UART2 |
| 1 | SW_Push | SW_Push_1P1T-SH_NO_CK_KMR2xxG | SW1 |
| 2 | Conn_01x10_Pin | PinSocket_1x10_P1.00mm_Vertical | UART3_XBEE1, UART3_XBEE2 |
| 2 | 2.2UF 22pF | C_0402_1005Metric | C1, C2 |
| 1 | 100 nF | C_0402_1005Metric | C3 |
| 1 | 100nF | C_0402_1005Metric | C4 |
| 3 | 100NF 100 nF | C_0402_1005Metric | C5, C6, C7 |
| 1 | 10K 10 k | R_0402_1005Metric | R3 |
SkyOrcaRX design files
The KiCad project lives in the mohamedaminemb/SkyOrca-Hardware repository on GitHub; these links point at the commit this page was built from.
SkyOrcaRX: common questions
What microcontroller does the SkyOrcaRX use?
The SkyOrcaRX is built around the STM32F405RGTX, from the STM32 family.
How big is the SkyOrcaRX PCB?
The SkyOrcaRX measures 32 × 25 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the SkyOrcaRX?
16 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SkyOrcaRX design files?
From the mohamedaminemb/SkyOrca-Hardware repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the SkyOrcaRX design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which mohamedaminemb chose for the repository.
Can I test firmware for the SkyOrcaRX without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in SkyOrca-Hardware
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k