Wdd2-pick and place arm
NathanSpalding·wdd2-pick-and-place-arm·electronics/schematic/wdd2-pick-and-place-schematic/wdd2-pick-and-place-schematic.kicad_sch
About the Wdd2-pick and place arm PCB
Wdd2-pick and place arm is an open source PCB design by NathanSpalding, published on GitHub under the MIT license. It is a board, with 22 components from 12 distinct parts.
Other key parts include the XL4016 #1, XL4016 #2 and XL4016 #3. By type, the board carries 11 ICs, 7 connectors, 2 fuses and 2 capacitors.
It belongs with the robotics & motion designs in this gallery.
From the project
Low-cost 4-DOF pick-and-place arm with joint encoders and current-based grasp detection (Stellenbosch Mechatronic Project 478, 2026)
- KiCad project: the schematics as drawn for the build. - schematicredrawn.pdf / .tex: the single-sheet circuit from Appendix B of the report (circuitikz source). - BOM.xlsx / BOM.csv`: every part with quantity, price, supplier link and printed-part masses.
The 12 V supply passes through a 15 A fuse and a relay held by the latching emergency stop. Pressing the stop cuts all three servo rails; the logic stays on.
Main components on the Wdd2-pick and place arm
Wdd2-pick and place arm bill of materials (BOM)
22 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XL4016 #1 | U1 | |
| 1 | XL4016 #2 | U2 | |
| 1 | XL4016 #3 | U3 | |
| 8 | — | U4, U5, U6, U7, U8–Base(ch0), U9–Shoulder(ch1), U10–Elbow(ch2), U11–Wrist(ch3) | |
| 1 | DS5180 | J5 | |
| 1 | XT60 Connector | J7 | |
| 3 | DS3240 | J9, J12, J13 | |
| 1 | DS3225 | J10 | |
| 1 | MG996R | J11 | |
| 2 | 15A | F1, F2 | |
| 1 | 100nF | C2 | |
| 1 | 4700µF | C3 |
Wdd2-pick and place arm design files
The KiCad project lives in the NathanSpalding/wdd2-pick-and-place-arm repository on GitHub; these links point at the commit this page was built from.
Wdd2-pick and place arm: common questions
How many components are on the Wdd2-pick and place arm?
22 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Wdd2-pick and place arm design files?
From the NathanSpalding/wdd2-pick-and-place-arm repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Wdd2-pick and place arm design in my own project?
Yes, under the terms of its MIT license, which NathanSpalding chose for the repository.
Similar boards
Stack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kCube batteryboard
willem-pennings
95 × 95 mm4 parts2LGPL-3.01.1kTrollerv2
rene-dev
100 × 75 mm33 parts4LGPL-3.0979Powerstep
rene-dev
95.2 × 71.5 mm28 parts4LGPL-3.097911ua
rene-dev
57.3 × 19 mm26 parts2LGPL-3.0979Diff driver
rene-dev
32 × 22 mm14 parts2LGPL-3.0979