Midi-Thing
NestOfGhosts·Midi-Thing·v2/v2.kicad_pcb
About the Midi-Thing PCB
Midi-Thing is an open source NXP PCB design by NestOfGhosts, published on GitHub. It is a 2-layer board measuring 136 × 96 mm, with 16 components from 4 distinct parts.
Its main chip is the Teensy4.0_AudioShield_REVD, from the NXP family. By type, the board carries 13 switches, 1 IC and 1 resistor.
It belongs with the audio and keyboards designs in this gallery.
From the project
Basic midi device, also can be played live with headphones
- PCB: use the production files and a pcb printing service like JLCPCB to get.
- Switches and caps: use whatever as long as is cherry mx 5 pin compatible
- Enter the teensy's bootloader mode by pressing the button. You can tell it works if the led turns off
- Load firmware.hex using the Teensy Loader
- Solder the teensy onto the shield, and the shield to the pcb (using the header pins).
Main components on the Midi-Thing
Midi-Thing bill of materials (BOM)
16 components, 4 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Teensy4.0_AudioShield_REVD | 4.0audioshield | U1 |
| 1 | R_Potentiometer | Potentiometer_Alpha_RD901F-40-00D_Single_Vertical | RV1 |
| 13 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +5 |
| 1 | PTA3043-2010CIB103 | TRIM_PTA3043-2010CIB103 | R1 |
Midi-Thing design files
The KiCad project lives in the NestOfGhosts/Midi-Thing repository on GitHub; these links point at the commit this page was built from.
- Layoutv2/v2.kicad_pcb
- Schematicv2/v2.kicad_sch
Midi-Thing: common questions
What microcontroller does the Midi-Thing use?
The Midi-Thing is built around the Teensy4.0_AudioShield_REVD, from the NXP family.
How big is the Midi-Thing PCB?
The Midi-Thing measures 136 × 96 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Midi-Thing?
16 components, from 4 distinct parts. The full bill of materials is listed on this page.
Where can I download the Midi-Thing design files?
From the NestOfGhosts/Midi-Thing repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Midi-Thing design in my own project?
The repository has no license, so all rights stay with NestOfGhosts. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Midi-Thing without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
Similar boards
NXP
32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763NXP
Mega-Cube-Board
MaltWhiskey
200 × 54 mm100 parts4LNo license763NXP
MCL6809
MicroCoreLabs
32.3 × 61 mm7 parts4LNo license532NXP
MCL68
MicroCoreLabs
31.6 × 84.1 mm13 parts4LNo license532NXP
MCL65+
MicroCoreLabs
72.6 × 64.1 mm6 parts2LNo license532NXP
MCLZ8
MicroCoreLabs
37.1 × 61.5 mm6 parts4LNo license532