Cs pogo adapter
About the Cs pogo adapter PCB
Cs pogo adapter is an open source PCB design by Nitrokey, published on GitHub. It is a 2-layer board measuring 26 × 42 mm, with 10 components from 9 distinct parts.
By type, the board carries 8 connectors and 2 resistors.
It belongs with the usb & debug tools designs in this gallery.
From the project
J8 and J9 are different types of pads used on different target PCBs. They are all connected together to make testing easier.
J8 and J9 are different types of pads used on different target PCBs. They are all connected together to make testing easier.
R1 and R2 are required depending on whether you use Versaloon or ST-Link programmer.
R1 is used to power the target device when using ST-Link. ST-Link doesn't provide power to the target board normally, but it has 3.3V on pin 19 of the JTAG connector (which is normally not connected on the target board).
Cs pogo adapter bill of materials (BOM)
10 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | HEADER_6 | POGO6-oval | J1 |
| 1 | WM3983 | vasch_strip_10x2 | J2 |
| 1 | — | pin_strip_4 | J3 |
| 1 | HEADER_4 | SIL-2-2-guiding_holes | J4 |
| 1 | HEADER_6 | POGO6-oval-offset | J6 |
| 1 | HEADER_4 | SIL-2-2-guiding_holes-offest | J7 |
| 1 | HEADER_4 | SIL-2-2-drilled-guiding_holes | J8 |
| 1 | HEADER_4 | SIL-2-2-drilled-guiding_holes-offset | J9 |
| 2 | 0 | r_0805 | R1, R2 |
Cs pogo adapter design files
The KiCad project lives in the Nitrokey/nitrokey-start-hardware repository on GitHub; these links point at the commit this page was built from.
Cs pogo adapter: common questions
How big is the Cs pogo adapter PCB?
The Cs pogo adapter measures 26 × 42 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Cs pogo adapter?
10 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Cs pogo adapter design files?
From the Nitrokey/nitrokey-start-hardware repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Cs pogo adapter design in my own project?
The repository has no license, so all rights stay with Nitrokey. Use it as a reference, and ask the author before reusing the design.
More boards in nitrokey-start-hardware
Similar boards
FW-EC-DongleHiderPlus
LeoDJ
28.2 × 26.1 mm14 parts4LCERN-OHL-W-2.0490
Relatively-Universal-ROM-Programmer
AndersBNielsen
68.8 × 53.6 mm141 parts2LGPL-3.0253
Ovc5
osrf
98 × 97 mm197 parts6LApache-2.0208
Easy pdk programmer hardware
free-pdk
26.7 × 21.6 mm28 parts2LCC-BY-SA-4.0206
27c160-tl866-adapter
mafe72
82.4 × 43.1 mm10 partsGPL-3.0147
STM32 VGM Player YM2612 SN76489
AidanHockey5
138.4 × 91.4 mm84 parts2LAGPL-3.0117