Phantom 3 pro flight ctrl board
About the Phantom 3 pro flight ctrl board
Phantom 3 pro flight ctrl board is an open source STM32 PCB design by o-gs, published on GitHub. It is a 2-layer board measuring 38 × 30 mm, with 15 components from 12 distinct parts.
Its main chip is the STM32F427II, from the STM32 family. Other key parts include the MS5607, MPU-6500, PA 5xA and RC09. By type, the board carries 7 resistors, 5 ICs and 3 connectors.
It belongs with the robotics & motion designs in this gallery.
From the project
Community made schematics for the DJI drones and devices.
The repository stored KiCad projects with schematocs and PCBs of various parts of DJI hardware. These projects are community made, and very likely have errors. They come with no warranty.
If you see an error in a schematic, or want to contribute your own - you are free to do it. Your contribution will be verified and accepted into this repository.
Main components on the Phantom 3 pro flight ctrl board
Phantom 3 pro flight ctrl board bill of materials (BOM)
15 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F427II | BGA-176p25_10x10_11.0x11.0mm_Pitch0.65mm | U1 |
| 1 | MS5607 | LGA-8_3x5mm_Pitch1.25mm | U2 |
| 1 | MPU-6500 | QFN-24_3x3mm_Pitch0.4mm | U3 |
| 1 | PA 5xA | DFN-8-1EP_3x3mm_Pitch0.65mm | U5 |
| 1 | RC09 | TSOT-23-5 | U6 |
| 1 | Micro_SD_Card | microSD_Card_Receptacle_Wuerth_693072010801 | J1 |
| 1 | CONN_MC_FRONT | Connector-edge-20pin-1.78mm-cut | J8 |
| 1 | CONN_MC_BACK | Connector-edge-21pin-1.78mm-cut | J9 |
| 2 | 22Ω | R_0201 | R1, R4 |
| 3 | 10kΩ | R_0201 | R2, R5, R7 |
| 1 | 15,7kΩ | R_0201 | R3 |
| 1 | 100Ω | R_0201 | R6 |
Phantom 3 pro flight ctrl board design files
The KiCad project lives in the o-gs/dji-hardware-schematics repository on GitHub; these links point at the commit this page was built from.
Phantom 3 pro flight ctrl board: common questions
What microcontroller does the Phantom 3 pro flight ctrl board use?
The Phantom 3 pro flight ctrl board is built around the STM32F427II, from the STM32 family.
How big is the Phantom 3 pro flight ctrl board?
The Phantom 3 pro flight ctrl board measures 38 × 30 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Phantom 3 pro flight ctrl board?
15 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Phantom 3 pro flight ctrl board design files?
From the o-gs/dji-hardware-schematics repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Phantom 3 pro flight ctrl board design in my own project?
The repository has no license, so all rights stay with o-gs. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Phantom 3 pro flight ctrl board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in dji-hardware-schematics
Similar boards
STM32LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7k
STM32AxxSolder
AxxAxx
39 × 82.5 mm122 parts2LGPL-3.01.7k
STM32AIOC
skuep
21 × 31.5 mm47 parts2LMIT1.4k
STM32Ferris
pierrechevalier83
208.8 × 86.8 mm102 parts2LSHL-2.11.3k
STM32176 pin board
rusefi
61.8 × 73.2 mm76 parts2LGPL-3.01.2k
STM32Brain board STM32F407
61.8 × 73.2 mm69 parts2LGPL-3.01.2k