28 open source boards using the MPU-6500
Real designs built with the MPU-6500, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Monolith
luftaquila
96 × 74.4 mm112 parts2LCustom license43STM32
PCB FujitoraBot2
OPRobots
95.6 × 100 mm99 parts2LAGPL-3.019STM32
ProPrj Project Ignis 2026-06-03
Shourya-x
123.2 × 67.9 mm71 parts2LNo license3ESP32
Mad Bot
Incomprehensible
133.2 × 115.3 mm88 parts4LMIT1RP2040/RP2350
Fredboard
Thebucket-ops
51 × 21 mm41 parts2LMIT1Telemetry System
BCIT-BAJA
99.9 × 99.9 mm88 parts4LNo license0STM32
Rokisi
mdumas2
79.1 × 82 mm73 parts2LBSD-3-Clause0ESP32
FC ESP32
PNT2110
79.8 × 79.8 mm72 parts2LNo license0STM32
Flight controller
epicgrowl
50 × 50 mm59 parts4LNo license0Acro
chickadee-tech
36 × 36 mm21 parts2LCC-BY-4.00ESP32
RocketLog
jacobjuneau6
25 × 75 mm11 parts2LAGPL-3.00RP2040/RP2350
Hermes
NoIwantyourcode
61.4 × 38.2 mm8 parts2LNo license0ESP32
Monolith mini
luftaquila
51.6 × 74.4 mm58 parts2LCustom license43ESP8266
Merlyn435
YeetTheAnson
30.5 × 30.5 mm69 parts4LNo license4ESP32
Before candidate promotion
PNT2110
79.8 × 79.8 mm72 parts2LNo license0STM32
Phantom 3 pro flight ctrl board
o-gs
38 × 30 mm15 parts2LNo license246ESP32
Epdiy v7-raw
vroland
128.4 × 74.9 mm105 parts4LCC-BY-SA-4.074STM32
Quatro
Teruru-52
100 × 72.8 mm98 parts2LNo license1ESP32
Before feedback restore
PNT2110
79.8 × 79.8 mm72 parts2LNo license0ESP32
Before local repair
PNT2110
79.8 × 79.8 mm72 parts2LNo license0ESP32
Before pnt
PNT2110
79.8 × 79.8 mm72 parts2LNo license0ESP32
C3 candidate
PNT2110
79.8 × 79.8 mm72 parts2LNo license0ESP32
C3 rotated before adc rip
PNT2110
79.8 × 79.8 mm72 parts2LNo license0ESP32
Final routed
PNT2110
79.8 × 79.8 mm72 parts2LNo license0ESP32
Header routed baseline
PNT2110
79.8 × 79.8 mm72 parts2LNo license0ESP32
One connection remaining
PNT2110
79.8 × 79.8 mm72 parts2LNo license0ESP32
Only c3 ground remaining
PNT2110
79.8 × 79.8 mm72 parts2LNo license0ESP32
Route import.tmp
PNT2110
79.8 × 79.8 mm72 parts2LNo license0
How designs wire the MPU-6500
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the MPU-6500 connects to, and the resistors, capacitors and other passives placed on it.
- The REGOUT pin has a capacitor to GND on 14 of 16 designs, most often 100 nF (then 10 nF).
- The NC_1 pin is left unconnected on 16 of 16 designs.
- The NC_2 pin is left unconnected on 16 of 16 designs.
- The NC_3 pin is left unconnected on 16 of 16 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NC_1pin 1 | Connected to: Not connected 100% | — |
| NC_2pin 2 | Connected to: Not connected 100% | — |
| NC_3pin 3 | Connected to: Not connected 100% | — |
| NC_4pin 4 | Connected to: Not connected 100% | — |
| NC_5pin 5 | Connected to: Not connected 100% | — |
| NC_6pin 6 | Connected to: Not connected 100% | — |
| AUX_CLpin 7 | Connected to: Not connected 100% | — |
| VDDIOpin 8 | Connected to: 3.3V 94% |
|
| REGOUTpin 10 | Connected to: Signal 81% |
|
| FSYNCpin 11 | Connected to: GND 69% · not connected 25% | — |
| VDDpin 13 | Connected to: 3.3V 94% |
|
| NCpin 14, 15, 16, 17 | Connected to: Not connected 100% | — |
| GNDpin 18 | Connected to: GND 100% | — |
| RESV_1pin 19 | Connected to: Not connected 88% | — |
| RESV_2pin 20 | Connected to: GND 88% | — |
| AUX_DApin 21 | Connected to: Not connected 100% | — |
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Phantom 3 pro flight ctrl board by o-gs, Epdiy v7-raw by vroland, Monolith by luftaquila and PCB FujitoraBot2 by OPRobots.
The MPU-6500 in open source designs
The gallery holds 28 open source boards using the MPU-6500 from 16 GitHub repositories; a typical one measures about 79.8 × 79.8 mm and carries around 72 components.
82% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is Phantom 3 pro flight ctrl board by o-gs.
Parts used alongside the MPU-6500
Microcontrollers on boards using the MPU-6500
What boards using the MPU-6500 are built for
MPU-6500: common questions
Where can I find a MPU-6500 reference design?
Each of the 28 boards on this page is a real design using the MPU-6500. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MPU-6500 REGOUT pin connected?
The REGOUT pin has a capacitor to GND on 14 of 16 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 16 open source designs using the MPU-6500.
How is the MPU-6500 NC_1 pin connected?
The NC_1 pin is left unconnected on 16 of 16 designs. Counted from the KiCad layouts of 16 open source designs using the MPU-6500.
How is the MPU-6500 NC_2 pin connected?
The NC_2 pin is left unconnected on 16 of 16 designs. Counted from the KiCad layouts of 16 open source designs using the MPU-6500.
What parts are used alongside the MPU-6500?
The AMS1117-3.3, BMM150 and ESP32-S3-WROOM-1-N8R8 appear in the most repositories here.
Which microcontrollers do boards using the MPU-6500 use?
Most are built on ESP32 (17), STM32 (6), RP2040/RP2350 (2) and ESP8266 (1).
How big is a typical board using the MPU-6500?
The median is 79.8 × 79.8 mm, and 82% are two-layer designs.
What is the most popular open source board using the MPU-6500?
By GitHub stars, Phantom 3 pro flight ctrl board by o-gs, with 246 stars.
Can I simulate one of these boards using the MPU-6500 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.