SLD-KIT-DICE
OLIMEX·SLD-KIT-DICE·HARDWARE/SLD-KIT-DICE_Rev_A/SLD-KIT-DICE_Rev_A.kicad_pcb
About the SLD-KIT-DICE PCB
SLD-KIT-DICE is an open source RISC-V PCB design by OLIMEX, published on GitHub under the MIT license. It is a 2-layer board measuring 40 × 40 mm, with 22 components from 12 distinct parts.
Its main chip is the CH32V003J4M6(SOP8), from the RISC-V family. By type, the board carries 7 LEDs, 7 resistors, 1 IC, 1 transformer, 1 diode and 1 capacitor.
It belongs with the sensors designs in this gallery.
From the project
Soldering Kit of electronic DICE with motion sensor and CH32V003 microcontroller
Electronic dice soldering kit: shake it, and it spins with sound and lands on a random number.
- CH32V003J4M6 RISC-V microcontroller, 7 LEDs, shock sensor, speaker - One CR2032 coin cell, ~6 µA in standby - Through-hole parts only, except the SOP-8 microcontroller
Connect a WCH-LinkE to the PGM/DBG header: pin 1 = SWIO, pin 2 = GND. The header has no VCC, so the battery must be in. The chip accepts the programmer only in the first 3 s after the battery is put in: start the command, then put the battery in.

Main components on the SLD-KIT-DICE
SLD-KIT-DICE bill of materials (BOM)
22 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH32V003J4M6(SOP8) | SOIC-8_150mil | U1 |
| 1 | CR2032H PTH | CR2032H_PTH | BAT1 |
| 1 | NA(HN1x2) | HN1x2 | PGM/DBG1 |
| 1 | SNS-SHOCK | SNS-SHOCK-SENSOR | SH_Sens1 |
| 1 | Speaker_QMB-09B-03(1.5-5.0V_2.7kHz_F9.0mm*H5.5mm) | Speaker_QMB-09B-03_1-Plus_2-Minus | SPK1 |
| 1 | 2N3904 | TO-92_PTH | T1 |
| 7 | LED/PTH/5MM/RED 5MM/RED/5000mCd | LED-5mm-PTH-KA | LED1, LED2, LED3, LED4, LED5, LED6, LED7 |
| 1 | 1N4148/DO35 | DO35_1K_2A | D1 |
| 1 | 100NF/25V/2010 100nF/25V/2010 | C2010 | C1 |
| 1 | NA(10k/1/8W) | R_0.125W_PTH | R1 |
| 5 | 100R/1/8W | R_0.125W_PTH | R2, R3, R4, R5, R6 |
| 1 | 1K/1/8W 1k/1/8W | R_0.125W_PTH | R7 |
SLD-KIT-DICE design files
The KiCad project lives in the OLIMEX/SLD-KIT-DICE repository on GitHub; these links point at the commit this page was built from.
SLD-KIT-DICE: common questions
What microcontroller does the SLD-KIT-DICE use?
The SLD-KIT-DICE is built around the CH32V003J4M6(SOP8), from the RISC-V family.
How big is the SLD-KIT-DICE PCB?
The SLD-KIT-DICE measures 40 × 40 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SLD-KIT-DICE?
22 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SLD-KIT-DICE design files?
From the OLIMEX/SLD-KIT-DICE repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the SLD-KIT-DICE design in my own project?
Yes, under the terms of its MIT license, which OLIMEX chose for the repository.
Can I test firmware for the SLD-KIT-DICE without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RISC-V firmware against it before you order a PCB.
Similar boards
RISC-V
Audio
byrantech
27.8 × 22.3 mm38 parts2LMIT4.3kRISC-V
Keybit
notaroomba
19.1 × 19.1 mm19 parts2LNo license438RISC-V
Workbench-1 Controller
Quchaosheng
160 × 130 mm106 parts8LApache-2.0212RISC-V
Froggyswadge
cnlohr
81.5 × 72.2 mm92 parts2LMIT105RISC-V
Keytartouch
cnlohr
152.5 × 117.5 mm69 parts2LMIT105RISC-V
Ch32v003f4u6 with wsled
cnlohr
40.6 × 44.5 mm26 parts2LMIT105