Hotswap toolhead

pinkfish·hotswap_toolhead·hardware/toolhead.kicad_pcb

Hotswap toolhead PCB layout, top view — open source STM32 board by pinkfish

About the Hotswap toolhead PCB

Hotswap toolhead is an open source STM32 PCB design by pinkfish, published on GitHub under the Apache-2.0 license. It is a 4-layer board measuring 31 × 42 mm, with 72 components from 46 distinct parts.

Its main chip is the STM32G0B1CBU6, from the STM32 family. Other key parts include the LMR16006XDDC, TCAN3414DR and USBLC6-2SC6. By type, the board carries 23 resistors, 19 capacitors, 8 diodes, 4 ICs, 4 connectors and 3 transistors.

From the project

24 V CAN toolhead board: heater, fan, thermistor, USB debug (STM32G0B1, Klipper)

The schematic is generated from tools/design.py (the netlist) by tools/genkicad.py`; the PCB is routed. Opens in KiCad 8 or newer (routed and checked in KiCad 10).

The schematic was checked by re-parsing the file and rebuilding the netlist from pin and label positions: every pin matches tools/design.py, with no dangling pins.

- Stackup: F.Cu (connectors, buttons, LEDs, C1, JP2; GND pour), In1 solid GND, In2 solid +24V, B.Cu (all other parts; GND pour). Signals route on F.Cu and B.Cu only. - Heater current path: J1 pin 1 → VINRAW pour (B.Cu) → F1 → VINF pour (B.Cu) → Q1 → +24V pour on Q1's…

Main components on the Hotswap toolhead

Hotswap toolhead bill of materials (BOM)

72 components, 46 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
LMR16006XDDC
U1
1
TCAN3414DR
U3
1
USBLC6-2SC6
U5
1
STM32G0B1CBU6
U6
1
SQJ461EP-T1_GE3
Q1
1
N-FET 60V <=30mR@2.5V
Q2
1
WST6066A
Q3
1
C9002
8MHz 20pF 3225
Y1
1
C19268030
XT30PW(2+2)-M.G.B
J1
1
C564339
Heater (Nano-Fit 2)
J2
1
C586245
Fan/therm/sensor (Nano-Fit 2x3)
J3
1
C165948
USB-C (HRO TYPE-C-31-M-12)
J5
1
C49328461
6A 1206 fuse (BSMD1206C-1600T)
F1
1
C369169
PTC 0.75A 33V (JK-mSMD075-33)
F2
1
TERM
JP1
1
NTC/PT1000
JP2
1
C528965
RESET
SW1
1
C528965
BOOT
SW2
1
C2289
yellow-green
LED1
1
C2288
blue
LED2
Show 26 more
QtyPartRefs
1
SMAJ33CA
D1
1
C19077426
MMSZ5242B 12V
D2
4
C22466354
DSK110 100V 1A
D3, D5, D7, D9
1
NUP2105L
D4
1
BAT54S
D6
1
C76884
600R@100MHz
FB1
1
C167883
22uH 1.2A (FNR4030S220MT)
L1
1
C72523
47uF 50V 105C
C1
3
C13585
10uF 50V X5R
C2, C3, C4
1
100NF
100nF
C5
7
100NF
100nF
C6, C9, C12, C15, C16, C19, C20
1
C12891
22uF 25V X5R
C8
2
C15850
10uF 25V X5R
C10, C17
1
1UF
1uF
C11
2
C1562
33pF C0G
C13, C14
1
100nF 50V
C18
6
10K
10k
R1, R3, R13, R14, R16, R22
1
33K
33k
R2
5
1k
R4, R5, R15, R19, R23
1
100R
R6
2
C17168
0R
R7, R8
3
0R
R9, R10, R12
1
120R
R11
1
C281778
4.7k 0.1% 25ppm
R17
1
C852812
4.12k 0.1% 25ppm
R18
2
5.1K
5.1k
R20, R21

Hotswap toolhead design files

The KiCad project lives in the pinkfish/hotswap_toolhead repository on GitHub; these links point at the commit this page was built from.

Hotswap toolhead: common questions

What microcontroller does the Hotswap toolhead use?

The Hotswap toolhead is built around the STM32G0B1CBU6, from the STM32 family.

How big is the Hotswap toolhead PCB?

The Hotswap toolhead measures 31 × 42 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Hotswap toolhead?

72 components, from 46 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Hotswap toolhead design files?

From the pinkfish/hotswap_toolhead repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Hotswap toolhead design in my own project?

Yes, under the terms of its Apache-2.0 license, which pinkfish chose for the repository.

Can I test firmware for the Hotswap toolhead without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards