Steel form Dish washer PART 1
About the Steel form Dish washer PART 1 PCB
Steel form Dish washer PART 1 is an open source AVR/Arduino PCB design by R-Mutura, published on GitHub. It is a 4-layer board measuring 185 × 95 mm, with 127 components from 80 distinct parts.
Its main chip is the LM1117-3.3, from the AVR/Arduino family. Other key parts include the MAX31865ATP+T, ATMEGA2560-16AU and MOC3021. By type, the board carries 45 resistors, 17 connectors, 16 capacitors, 13 diodes, 8 ICs and 6 transistors.
From the project
Contains hardware and Software implementation of a dishwasher product
Main components on the Steel form Dish washer PART 1
Steel form Dish washer PART 1 bill of materials (BOM)
127 components, 80 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MAX31865ATP+T LM358 | SO-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | MAX31865ATP+T AMS1117-3.3 | SOT-223 | U2 |
| 1 | LM1117-3.3 ATmega2560-16AU | TQFP-100_14x14mm_P0.5mm | U3 |
| 1 | ATMEGA2560-16AU EL817 | DIP-4_W7.62mm | U4 |
| 4 | MOC3021 Lite-On Inc. | DIP-6_W7.62mm | U5, U6, U7, U8 |
| 3 | mmbt3904 | SOT-23 | Q1, Q2, Q3 |
| 1 | DMP6250SE-13 AP2301 | SOT-23 | Q4 |
| 2 | WST2N7002K mmbt3904 | SOT-23 | Q5, Q6 |
| 1 | S3216000091060 16MHz | Crystal_SMD_SeikoEpson_FA238-4Pin_3.2x2.5mm | Y1 |
| 1 | RTD_BOILER_SENSOR | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J1 |
| 1 | AC_PWR_IN | KF8500-4PIN | J2 |
| 1 | 387207505 RTD_TANK_SENSOR | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J3 |
| 1 | MAG_DOOR_SENSOR | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J4 |
| 1 | Z-231011814106 Conn_02x07_Odd_Even | IDC-Header_2x07_P2.54mm_Vertical | J5 |
| 1 | 210-72-03GB01 Conn_02x03_Odd_Even | PinHeader_2x03_P2.54mm_Vertical | J6 |
| 1 | 210-91-04GB01 Conn_01x04_Male | PinSocket_1x04_P2.54mm_Vertical | J7 |
| 1 | DB128V-5.0-4P-GN-S Conn_01x03_Male | TerminalBlock_Phoenix_MKDS-1,5-3-5.08_1x03_P5.08mm_Horizontal | J8 |
| 1 | DB128V-5.0-4P-GN-S WASH PUMP CONNECTOR | SHDR2W100P0X508_1X2_1070X900X1380P | J9 |
| 1 | XY126V-5.0-2P SOLENOID CONNECTOR | SHDR2W100P0X508_1X2_1070X900X1380P | J10 |
| 1 | XY126V-5.0-2P DRAIN PUMP CONNECTOR | SHDR2W100P0X508_1X2_1070X900X1380P | J11 |
Show 60 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 6PCV_04_006 BOILER HEATER CONNECTOR | KF8500-4PIN | J12 |
| 1 | Pressure Switch 1 | JST_EH_S3B-EH_1x03_P2.50mm_Horizontal | J13 |
| 1 | Pressure Switch 2 | JST_EH_S3B-EH_1x03_P2.50mm_Horizontal | J14 |
| 1 | XY126V-5.0-2P peristaltic_pump_1 | SHDR2W100P0X508_1X2_1070X900X1380P | J15 |
| 1 | XY126V-5.0-2P peristaltic_pump_2 | SHDR2W100P0X508_1X2_1070X900X1380P | J16 |
| 1 | 6PCV02006 TANK HEATER | KF8500-2PIN | J17 |
| 1 | PS1240P02BT TDK Corporation | Piezo_Transducer_THT_PS1240P02BT | BZ1 |
| 6 | 9-1440003-0 SRA-05VDC-CL | SRA-05VDC-CL | K1, K2, K3, K4, K5, K6 |
| 1 | HLK-5M05 HLK-PM01 | Converter_ACDC_HiLink_HLK-PMxx | PS1 |
| 9 | CNR-10D511KBTSA | RV_Disc_D15.5mm_W5.9mm_P7.5mm | RV1, RV2, RV3, RV4, RV5, RV6, RV10, RV11 +1 |
| 3 | VDR-14D181K | RV_Disc_D15.5mm_W5.9mm_P7.5mm | RV7, RV8, RV9 |
| 1 | K2-1187SQ-D4SW-06 SW_Push | K2-1187SQ-D4SW-06 | SW1 |
| 1 | SZYY0603R LED_Small | LED_0603_1608Metric | D1 |
| 1 | SZYY0603B LED_Small | LED_0603_1608Metric | D2 |
| 1 | MB6S | TO-269AA | D3 |
| 6 | B5819WS | D_SOD-323 | D4, D5, D6, D10, D11, D12 |
| 4 | MAC223A6,127 Q_TRIAC_A1A2G | TO-220-3_Vertical | D7, D8, D9, D13 |
| 1 | CC0402KRX5R9BB104 10uF | C_0402_1005Metric | C1 |
| 1 | CC0402KRX5R9BB104 1uF | C_0402_1005Metric | C2 |
| 1 | CC0402MRX5R5BB106 100nF | C_0402_1005Metric | C3 |
| 1 | CC0402KRX5R6BB105 100nF | C_0402_1005Metric | C4 |
| 4 | 100nF | C_0402_1005Metric | C5, C6, C10, C12 |
| 1 | 100u | CP_Elec_5x5.4 | C7 |
| 2 | 22pF | C_0402_1005Metric | C8, C9 |
| 1 | 4.7nF | C_0402_1005Metric | C11 |
| 1 | RVT100UF10V67RV0036 100nF | C_0402_1005Metric | C13 |
| 2 | CC0402JRNPO9BN220 100nF | C_0402_1005Metric | C14, C15 |
| 1 | CC0402KRX5R9BB104 100nF | C_0402_1005Metric | C16 |
| 1 | AC0402FR-074K3L 10K | R_0402_1005Metric | R1 |
| 1 | AC0402FR-074K3L 1K | R_0402_1005Metric | R2 |
| 1 | RC0402FR-07200RL 10K | R_0402_1005Metric | R3 |
| 2 | RC0402FR-07523RL 10K | R_0402_1005Metric | R4, R6 |
| 2 | AC0402FR-0710KL 1K | R_0402_1005Metric | R5, R28 |
| 1 | RC0402FR-074K7L 200R | R_0402_1005Metric | R7 |
| 2 | RC0402FR-074K7L 10K | R_0402_1005Metric | R8, R10 |
| 1 | RC0402FR-074K7L 500R | R_0402_1005Metric | R9 |
| 1 | RC0402FR-0747KL 500R | R_0402_1005Metric | R11 |
| 1 | RC0402FR-0747KL 4.7k | R_0402_1005Metric | R12 |
| 1 | RC0402FR-07100RL 4.7k | R_0402_1005Metric | R13 |
| 2 | 4.7k | R_0402_1005Metric | R14, R15 |
| 2 | 47K | R_0805_2012Metric | R16, R17 |
| 1 | 100R | R_0603_1608Metric | R18 |
| 2 | 1K | R_0402_1005Metric | R19, R26 |
| 3 | 800R | R_0402_1005Metric | R20, R21, R22 |
| 3 | 10K | R_0402_1005Metric | R23, R24, R25 |
| 1 | RC0402FR-071KL 1K | R_0402_1005Metric | R27 |
| 1 | AC0402FR-0710KL 1M | R_0402_1005Metric | R29 |
| 1 | RC0402FR-071KL 1M | R_0402_1005Metric | R30 |
| 1 | RC0402FR-07200RL 1M | R_0402_1005Metric | R31 |
| 2 | RC0402FR-071KL 200R | R_0402_1005Metric | R32, R33 |
| 1 | AC0402FR-0710KL 200R | R_0402_1005Metric | R34 |
| 2 | RC0402FR-07100RL 10K | R_0402_1005Metric | R35, R37 |
| 2 | 0603WAJ0151T5E 10K | R_0402_1005Metric | R36, R39 |
| 1 | RC0402FR-07100RL 1K | R_0402_1005Metric | R38 |
| 1 | RC0402FR-07100RL 800R | R_0402_1005Metric | R40 |
| 1 | RC0603JR-074K7L 800R | R_0402_1005Metric | R41 |
| 1 | RC0603JR-074K7L 10K | R_0402_1005Metric | R42 |
| 1 | 0603WAF7502T5E 10K | R_0402_1005Metric | R43 |
| 1 | RC0603JR-074K7L 200R | R_0402_1005Metric | R44 |
| 1 | AC0402FR-071ML 10K | R_0402_1005Metric | R45 |
Steel form Dish washer PART 1 design files
The KiCad project lives in the R-Mutura/DISHWASHER repository on GitHub; these links point at the commit this page was built from.
Steel form Dish washer PART 1: common questions
What microcontroller does the Steel form Dish washer PART 1 use?
The Steel form Dish washer PART 1 is built around the LM1117-3.3, from the AVR/Arduino family.
How big is the Steel form Dish washer PART 1 PCB?
The Steel form Dish washer PART 1 measures 185 × 95 mm, has 4 copper layers and is 4.69 mm thick.
How many components are on the Steel form Dish washer PART 1?
127 components, from 80 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Steel form Dish washer PART 1 design files?
From the R-Mutura/DISHWASHER repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Steel form Dish washer PART 1 design in my own project?
The repository has no license, so all rights stay with R-Mutura. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Steel form Dish washer PART 1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in DISHWASHER
Similar boards
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k
AVR/ArduinoMegadesk
gcormier
41.7 × 32.2 mm23 parts2LGPL-3.0818
AVR/ArduinoEasyduino Atmega Nano
Hanqaqa
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746