7 open source boards using the MOC3021
Real designs built with the MOC3021, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Clean room slave
trieuhuyduc
165 × 110 mm207 parts2LNo license1Kicad project
Invisible-Luna
63.6 × 63.6 mm25 parts2LNo license1AVR/Arduino
Steel form Dish washer
R-Mutura
185 × 95 mm147 parts4LNo license0DMX-dimmer pack
hsiboy
100.1 × 100 mm90 partsNo license0Esp32-ac dimmer fan controller
arunsaispk12
150 × 100 mm3 parts2LMIT0AVR/Arduino
Steel form Dish washer PART 1
R-Mutura
185 × 95 mm127 parts4LNo license0Steel form Dish washer PART 2
R-Mutura
230 × 35 mm20 parts4LNo license0
How designs wire the MOC3021
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MOC3021 connects to, and the resistors, capacitors and other passives placed on it.
- The NC_3 pin is left unconnected on 5 of 5 designs.
- The NC_5 pin is left unconnected on 5 of 5 designs.
- Pin 6 has a series resistor on 4 of 5 designs, most often 1 kΩ (then 330 Ω).
- Pin 2 is tied to GND on 3 of 5 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 60% · not connected 20% · 5V 20% |
|
| Pin 2 | Connected to: GND 60% · a signal 40% | — |
| NC_3pin 3 | Connected to: Not connected 100% | — |
| NC_5pin 5 | Connected to: Not connected 100% | — |
| Pin 6 | Connected to: Signal 80% · not connected 20% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Kicad project by Invisible-Luna, Clean room slave by trieuhuyduc, Esp32-ac dimmer fan controller by arunsaispk12 and DMX-dimmer pack by hsiboy.
The MOC3021 in open source designs
The gallery holds 7 open source boards using the MOC3021 from 5 GitHub repositories; a typical one measures about 165 × 95 mm and carries around 90 components.
50% are two-layer designs, the rest use four layers or more, and 14% carry an open source license.
The most starred is Clean room slave by trieuhuyduc.
Microcontrollers on boards using the MOC3021
MOC3021: common questions
Where can I find a MOC3021 reference design?
Each of the 7 boards on this page is a real design using the MOC3021. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MOC3021 NC_3 pin connected?
The NC_3 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MOC3021.
How is the MOC3021 NC_5 pin connected?
The NC_5 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the MOC3021.
What resistor goes on the MOC3021 pin 6?
Pin 6 has a series resistor on 4 of 5 designs, most often 1 kΩ (then 330 Ω). Counted from the KiCad layouts of 5 open source designs using the MOC3021.
Which microcontrollers do boards using the MOC3021 use?
Most are built on AVR/Arduino (2) and ESP32 (1).
How big is a typical board using the MOC3021?
The median is 165 × 95 mm, and 50% are two-layer designs.
What is the most popular open source board using the MOC3021?
By GitHub stars, Clean room slave by trieuhuyduc, with 1 stars.
Can I simulate one of these boards using the MOC3021 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.