BadCable-USB-RubberDucky
rgomez31UAQ·BadCable-USB-RubberDucky·rev1/BadUSB.kicad_pcb
About the BadCable-USB-RubberDucky PCB
BadCable-USB-RubberDucky is an open source AVR/Arduino PCB design by rgomez31UAQ, published on GitHub under the CC-BY-4.0 license. It is a 2-layer board measuring 12 × 6 mm, with 6 components from 5 distinct parts.
Its main chip is the ATtiny85V-10SU, from the AVR/Arduino family. By type, the board carries 3 resistors, 1 IC, 1 connector and 1 diode.
From the project
Development and implementation: Joel Serna & Ernesto Sánchez
Development and implementation: Joel Serna & Ernesto Sánchez
PCB design: Rev0: Jorge Mata, Rev1, Rev2, Rev3, Rev3.1: Ignacio Díaz Álvarez
The developers and collaborators of this project do not earn money with this. You can invite me for a coffee to further develop Low-Cost hacking devices. If you don't invite me for a coffee, nothing happens, I will continue developing devices.

Main components on the BadCable-USB-RubberDucky
BadCable-USB-RubberDucky bill of materials (BOM)
6 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATtiny85V-10SU | SOIJ-8_5.3x5.3mm_P1.27mm | U1 |
| 1 | USB_A | PinHeader_1x04_P1.00mm_Vertical | J1 |
| 1 | D_Zener_x2_ACom_KKA | TSOT-23 | D1 |
| 2 | 68R | R_0402_1005Metric | R1, R2 |
| 1 | 1K5 | R_0402_1005Metric | R3 |
BadCable-USB-RubberDucky design files
The KiCad project lives in the rgomez31UAQ/BadCable-USB-RubberDucky repository on GitHub; these links point at the commit this page was built from.
BadCable-USB-RubberDucky: common questions
What microcontroller does the BadCable-USB-RubberDucky use?
The BadCable-USB-RubberDucky is built around the ATtiny85V-10SU, from the AVR/Arduino family.
How big is the BadCable-USB-RubberDucky PCB?
The BadCable-USB-RubberDucky measures 12 × 6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the BadCable-USB-RubberDucky?
6 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the BadCable-USB-RubberDucky design files?
From the rgomez31UAQ/BadCable-USB-RubberDucky repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the BadCable-USB-RubberDucky design in my own project?
Yes, under the terms of its CC-BY-4.0 license, which rgomez31UAQ chose for the repository.
Can I test firmware for the BadCable-USB-RubberDucky without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k