7 open source boards using the ATtiny85V-10SU
Real designs built with the ATtiny85V-10SU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Z-probe on smd resistors-2512
IvDm
15.3 × 19.3 mm17 parts2LGPL-3.0150AVR/Arduino
Crobagotchi
Chris-Johnston
33 × 55.9 mm10 parts2LMIT4AVR/Arduino
OutFox
ShaunPrice
96.5 × 96.5 mm88 parts2LApache-2.01AVR/Arduino
Snowflake ornament
Chris-Johnston
79 × 86.5 mm16 parts2LMIT0AVR/Arduino
BadCable-USB-RubberDucky
rgomez31UAQ
12 × 6 mm6 parts2LCC-BY-4.00AVR/Arduino
FlySensei Stack RPi
denjos007
90 × 65 mm89 parts4LNo license0AVR/Arduino
FlySensei Stack RPi
denjos007
90 × 65 mm45 parts4LNo license0
How designs wire the ATtiny85V-10SU
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ATtiny85V-10SU connects to, and the resistors, capacitors and other passives placed on it.
- The XTAL2/PB4 pin has a pull-up to VCC on 3 of 6 designs, most often 4.7 kΩ (then 68 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ~RESET~/PB5pin 1 | Connected to: A connector 67% · not connected 33% |
|
| XTAL1/PB3pin 2 | Connected to: Signal 100% |
|
| XTAL2/PB4pin 3 | Connected to: Signal 100% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| AREF/PB0pin 5 | Connected to: A connector 67% · not connected 17% |
|
| VCCpin 8 | Connected to: VCC 100% | — |
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Z-probe on smd resistors-2512 by IvDm, Crobagotchi by Chris-Johnston, OutFox by ShaunPrice and Snowflake ornament by Chris-Johnston.
The ATtiny85V-10SU in open source designs
The gallery holds 7 open source boards using the ATtiny85V-10SU from 6 GitHub repositories; a typical one measures about 79 × 65 mm and carries around 17 components.
71% are two-layer designs, the rest use four layers or more, and 71% carry an open source license.
The most starred is Z-probe on smd resistors-2512 by IvDm.
Microcontrollers on boards using the ATtiny85V-10SU
What boards using the ATtiny85V-10SU are built for
ATtiny85V-10SU: common questions
Where can I find a ATtiny85V-10SU reference design?
Each of the 7 boards on this page is a real design using the ATtiny85V-10SU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ATtiny85V-10SU XTAL2/PB4 pin?
The XTAL2/PB4 pin has a pull-up to VCC on 3 of 6 designs, most often 4.7 kΩ (then 68 Ω). Counted from the KiCad layouts of 6 open source designs using the ATtiny85V-10SU.
Which microcontrollers do boards using the ATtiny85V-10SU use?
Most are built on AVR/Arduino (7).
How big is a typical board using the ATtiny85V-10SU?
The median is 79 × 65 mm, and 71% are two-layer designs.
What is the most popular open source board using the ATtiny85V-10SU?
By GitHub stars, Z-probe on smd resistors-2512 by IvDm, with 150 stars.
Can I simulate one of these boards using the ATtiny85V-10SU before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.