Nmea pi hat
ronangaillard·nmea-pi-hat
About the Nmea pi hat
Nmea pi hat is an open source STM32 PCB design by ronangaillard, published on GitHub under the MIT license. It is a 2-layer board measuring 65 × 56 mm, with 51 components from 17 distinct parts.
Its main chip is the STM32F030CCTx, from the STM32 family. Other key parts include the LM1085-5.0 and MAX485E. By type, the board carries 15 capacitors, 13 resistors, 8 connectors, 7 ICs, 6 diodes and 1 switch.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
A raspberry pi hat to handle NMEA 0183 devices
Raspberry Pi B+ Hat ============================
Expansion Board ----------------------------
This is a project template for a Raspberry Pi B+ Hat.
This base project includes a PCB edge defined according to this specification. Both a thru-hole and a surface mount connector are provided, along with a different PCB edge for each. Just keep the PCB edge and connector type that you're using for your design and delete the others.

Main components on the Nmea pi hat
Nmea pi hat bill of materials (BOM)
51 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM1085-5.0 | TO-263-3_TabPin2 | U1 |
| 1 | STM32F030CCTx | LQFP-48_7x7mm | U2 |
| 5 | MAX485E | SOIC-8_W3.9mm | U3, U4, U5, U6, U7 |
| 1 | Conn_01x02_Male | JST_SH_SM02B-SRSS-TB_02x1.00mm_Angled | J1 |
| 1 | RPi_GPIO | Pin_Header_Straight_2x20 | J2 |
| 1 | Conn_02x03_Counter_Clockwise | SDL-106-X-XX_2x03 | J3 |
| 5 | Conn_01x03_Male | JST_SH_SM03B-SRSS-TB_03x1.00mm_Angled | J5, J6, J7, J8, J9 |
| 1 | Crystal | Crystal_SMD_HC49-SD_HandSoldering | 8MHz1 |
| 1 | SW_Push | Switch_Tactile_SMD_6x6mm | SW1 |
| 6 | LED | LED_0603_HandSoldering | D1, D2, D3, D4, D5, D6 |
| 1 | 10uF | L_0805_HandSoldering | C1 |
| 1 | 100uF | C_1206_HandSoldering | C2 |
| 11 | 0.1uF | C_0603_HandSoldering | C3, C4, C5, C6, C7, C8, C9, C10 +3 |
| 2 | 20pF | C_0603_HandSoldering | C11, C12 |
| 6 | 180R | R_0603_HandSoldering | R1, R2, R3, R5, R6, R7 |
| 2 | 10k | R_0603_HandSoldering | R4, R8 |
| 5 | 120R | R_0603_HandSoldering | R9, R10, R11, R12, R13 |
Nmea pi hat design files
The KiCad project lives in the ronangaillard/nmea-pi-hat repository on GitHub; these links point at the commit this page was built from.
- LayoutRPi_Hat.kicad_pcb
Nmea pi hat: common questions
What microcontroller does the Nmea pi hat use?
The Nmea pi hat is built around the STM32F030CCTx, from the STM32 family.
How big is the Nmea pi hat?
The Nmea pi hat measures 65 × 56 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Nmea pi hat?
51 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the Nmea pi hat design files?
From the ronangaillard/nmea-pi-hat repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Nmea pi hat design in my own project?
Yes, under the terms of its MIT license, which ronangaillard chose for the repository.
Can I test firmware for the Nmea pi hat without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k