ATtiny85-Catch me-BCL-1-v1.0

rsedak·ATtiny85-Catch-me-BCL-1-v1.0·design_files/attiny85_catch_me_bcl-1.kicad_pcb

ATtiny85-Catch me-BCL-1-v1.0 PCB layout, top view — open source AVR/Arduino board by rsedak

About the ATtiny85-Catch me-BCL-1-v1.0 PCB

ATtiny85-Catch me-BCL-1-v1.0 is an open source AVR/Arduino PCB design by rsedak, published on GitHub under the Custom license license. It is a 2-layer board measuring 78.1 × 64.7 mm, with 24 components from 7 distinct parts.

Its main chip is the ATtiny85, from the AVR/Arduino family. By type, the board carries 12 resistors, 7 diodes, 2 switches, 1 IC, 1 battery holder and 1 capacitor.

From the project

My friend Zvonimir Lapov asked me if I could design THT PCB which would be used in primary school student education. Purpose of 'Catch me BCL-1' module is student education. It shows advantages of charlieplexing with seven BI-color LEDs. This version is designed for the case when the BI-color LED has a brighter LED on pin 1.

Introduction ============ My friend Zvonimir Lapov asked me if I could design THT PCB which would be used in primary school student education. Purpose of 'Catch me BCL-1' module is student education. It shows advantages of charlieplexing with seven BI-color LEDs. This version is designed for the case when the BI-color LED has a brighter LED on pin 1. There are many variations of bi-color LEDs on the market, so you will need to define the resistors yourself.

ATtiny85-Catch me-BCL-1-v1.0, from the project README
From the project README

Main components on the ATtiny85-Catch me-BCL-1-v1.0

ATtiny85-Catch me-BCL-1-v1.0 bill of materials (BOM)

24 components, 7 distinct parts.

QtyPartRefs
1
ATtiny85
U1
1
Battery_Cell
BT1
1
SW_Push
SW1
1
SW_Push_SPDT
SW2
7
LED_Dual_AKA
D1, D2, D3, D4, D5, D6, D7
1
0.1uF
C1
12
120R
R1, R2, R3, R4, R5, R6, R7, R8 +4

ATtiny85-Catch me-BCL-1-v1.0 design files

The KiCad project lives in the rsedak/ATtiny85-Catch-me-BCL-1-v1.0 repository on GitHub; these links point at the commit this page was built from.

ATtiny85-Catch me-BCL-1-v1.0: common questions

What microcontroller does the ATtiny85-Catch me-BCL-1-v1.0 use?

The ATtiny85-Catch me-BCL-1-v1.0 is built around the ATtiny85, from the AVR/Arduino family.

How big is the ATtiny85-Catch me-BCL-1-v1.0 PCB?

The ATtiny85-Catch me-BCL-1-v1.0 measures 78.1 × 64.7 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the ATtiny85-Catch me-BCL-1-v1.0?

24 components, from 7 distinct parts. The full bill of materials is listed on this page.

Where can I download the ATtiny85-Catch me-BCL-1-v1.0 design files?

From the rsedak/ATtiny85-Catch-me-BCL-1-v1.0 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the ATtiny85-Catch me-BCL-1-v1.0 design in my own project?

It is published under Custom license, which limits how it may be reused; read the license before building on it.

Can I test firmware for the ATtiny85-Catch me-BCL-1-v1.0 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards